Town & Country Fireplaces TCWS.54NGST03D Installation Instructions Manual Download Page 10 | Manualshive

Page: 10 / 24

background image

Reinstalled
Side panel
retainer clips

Figure 14: Reinstalled side panel retainer clips.

14. Reinstall the side panel retainer clips (Figure 14) .

15. Place mesh burner tray over top of the burners so that its legs rest on the secondary floor. The side of the

tray with the mesh strip crossing over from one side to the other must be positioned over top of the pilot
assembly. Screw down the ends of the tray to the ledge of the side panels - two on each side (Figure 15).

Mesh cross-over must be positioned
over the pilot assembly

Figure 15: Burner Tray.

TCWS.54NGST03D_210417-24

5056.425181D

10

«
...
8
9
10
11
12
...
»

Summary of Contents for TCWS.54NGST03D

























Reviews:

No comments

Related manuals for TCWS.54NGST03D

Brand: VDO Pages: 91

Brand: CALEFFI Pages: 20

Brand: Valor Fires Pages: 60

Brand: Manfrotto Pages: 2

Brand: Makita Pages: 64

Brand: Lantus Pages: 5

Brand: yasuni Pages: 11

Brand: Olympus Pages: 2

Brand: Raven Pages: 70

Brand: Uebler Pages: 18

KO PROPO RTF 2002 ESC

Brand: Tamiya Pages: 2

Brand: Razorri Pages: 26

Brand: Celestron Pages: 24

Brand: Kasanova Pages: 22

Brand: Phonocar Pages: 6

Brand: Empire Comfort Systems Pages: 8

B-TRK502-02-01-SL

Brand: SRC Pages: 4

UNI G CHIMNEY 06

Brand: UNIPRODO Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands