Tower Hobbies Laser 200 Flatty Instruction Manual Download Page 10 | Manualshive

Page: 10 / 16

background image

10

❏

2. If using the FlightPower ESC, solder the motor and

battery connectors to the leads and use heat-shrink tubing
to protect the bullet connectors and solder joints. (As noted
in the front of the manual, the JST connector will have to be
replaced with a Deans micro.)

Cut

Cut

❏

3. Temporarily connect your aileron servo, ESC and battery

to your receiver and power the system up with your transmitter.

Also make sure the trims and sub-trims are centered in your

transmitter programming. Find the orientation on the aileron
servo arm that will be neutral as shown in the illustration, then
cut off the unused arms.

❏

4. Use a hobby knife to enlarge the holes in the servo arm

for the screws in the extended aileron servo arm, then join
the two with 1.5mm x 3mm Phillips screws and a drop of CA.

❏

5. Install the aileron servo and mount the servo arm with

the aileron pushrods. Glue the servo into position with foam-
safe CA or canopy glue.

«
...
8
9
10
11
12
...
»

Summary of Contents for Laser 200 Flatty

















Reviews:

No comments

Related manuals for Laser 200 Flatty

Brand: Faller Pages: 8

Brand: Faller Pages: 16

Brand: Faller Pages: 4

Brand: Faller Pages: 4

Brand: Faller Pages: 4

Brand: Faller Pages: 16

Brand: Faller Pages: 8

Brand: Faller Pages: 8

Brand: Faller Pages: 8

Brand: Faller Pages: 36

Brand: Faller Pages: 2

Brand: E sky Pages: 32

Z-Scale Ford F6 Truck Kit

Brand: EA Electronics Pages: 2

Weekend I-16 TYPE 10

Brand: Eduard Pages: 6

MINI-Z Racer MR-03N HM MINI COOPER S

Brand: Kyosho Pages: 2

Brand: Simplay3 Pages: 3

Fantasy Bowl Stadium Short Tribune

Brand: Tabletop Scenics Pages: 5

AERO SUBARU 30EP

Brand: KK Hobby Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands