4.4 INSTALL OF LOOSE PARTS - INTRODUCTION
A few elements will be disassembled from the machine main structure due to packaging and shipping requirements.
These loose parts should be installed as follows.
WARNING
Please tighten all bolts and nuts absolutely. Otherwise, may cause machine wobble or serious injury to the operator or
other persons.
-16-
Fig.4.3
A
Fixing to the floor
The machine must be fixed to the floor.
- Use bolt/nut A to level the feet to ensure machine is well
located.
- Put expansion bolts D into ground, use washer/lock
wahser C and hex nut B to fasten the bolts.
B
C
D
4.4
INSTALL OF LOOSE PARTS - INTRODUCTION
A few elements will be disassembled from the machine main structure due to packaging and shipping requirements.
These loose parts should be installed as follows.
WARNING
Please tighten all bolts and nuts absolutely. Otherwise, may cause machine wobble or serious injury to the operator or
other persons.
-12-
4.4.1 INSTALL EXTENSION TABLE
Tools Required for Assembly:
- Wrench 16mm
- L Wrench 5mm
- Install Rear extension tables A to main table C with bolt
1 and washer 2.
- Install Right extension tables B to main table C with bolt
1 and washer 2.
Fig.4.4.1
4.4.2 INSTALL BLADE GUARD
Tools Required for Assembly:
- L Wrench 6mm
- Install Blade guard A to Riving knife with part 2.
Fig.4.4.2
A
B
C
1 2
1
2
A
2
4.3 INSTALLATION ZONE CHARACTERISTICS
WARNING
It is prohibited to install the machine in explosive environments.
The installation zone must be selected evaluating the work space required depending on the dimension of the pieces
to be machined,and taking into account that a free space of at least 800 mm must be left around the machine.It is also
necessary to check The floor capacity and its surface, so that the machine base is evenly resting on its four supports.A
power outlet and a chip-suction system connection shall be closeto the selected machine setting and it must be
conveniently lighted (luminous intensity: 500 LUX).
4.4
INSTALL OF LOOSE PARTS - INTRODUCTION
A few elements will be disassembled from the machine main structure due to packaging and shipping requirements.
These loose parts should be installed as follows.
WARNING
Please tighten all bolts and nuts absolutely. Otherwise, may cause machine wobble or serious injury to the operator or
other persons.
-12-
4.4.1 INSTALL EXTENSION TABLE
Tools Required for Assembly:
- Wrench 16mm
- L Wrench 5mm
- Install Rear extension tables A to main table C with bolt
1 and washer 2.
- Install Right extension tables B to main table C with bolt
1 and washer 2.
Fig.4.4.1
4.4.2 INSTALL BLADE GUARD
Tools Required for Assembly:
- L Wrench 6mm
- Install Blade guard A to Riving knife with part 2.
Fig.4.4.2
A
B
C
1 2
1
2
A
2
4.3 INSTALLATION ZONE CHARACTERISTICS
WARNING
It is prohibited to install the machine in explosive environments.
The installation zone must be selected evaluating the work space required depending on the dimension of the pieces
to be machined,and taking into account that a free space of at least 800 mm must be left around the machine.It is also
necessary to check The floor capacity and its surface, so that the machine base is evenly resting on its four supports.A
power outlet and a chip-suction system connection shall be closeto the selected machine setting and it must be
conveniently lighted (luminous intensity: 500 LUX).
4.4
INSTALL OF LOOSE PARTS - INTRODUCTION
A few elements will be disassembled from the machine main structure due to packaging and shipping requirements.
These loose parts should be installed as follows.
WARNING
Please tighten all bolts and nuts absolutely. Otherwise, may cause machine wobble or serious injury to the operator or
other persons.
-12-
4.4.1 INSTALL EXTENSION TABLE
Tools Required for Assembly:
- Wrench 16mm
- L Wrench 5mm
- Install Rear extension tables A to main table C with bolt
1 and washer 2.
- Install Right extension tables B to main table C with bolt
1 and washer 2.
Fig.4.4.1
4.4.2 INSTALL BLADE GUARD
Tools Required for Assembly:
- L Wrench 6mm
- Install Blade guard A to Riving knife with part 2.
Fig.4.4.2
A
B
C
1 2
1
2
A
2
4.3 INSTALLATION ZONE CHARACTERISTICS
WARNING
It is prohibited to install the machine in explosive environments.
The installation zone must be selected evaluating the work space required depending on the dimension of the pieces
to be machined,and taking into account that a free space of at least 800 mm must be left around the machine.It is also
necessary to check The floor capacity and its surface, so that the machine base is evenly resting on its four supports.A
power outlet and a chip-suction system connection shall be closeto the selected machine setting and it must be
conveniently lighted (luminous intensity: 500 LUX).
-13-
Fig.4.4.4
4.4.4 INSTALL OUTRIGGER
- Put the outrigger C into the slot of sliding table A.
- Put the support rod D into the hole of outrigger C and
the hole on telescopic arm E.
Fig.4.4.3
A
B
C
4.4.3 INSTALL SLIDING TABLE
- Put the sliding table onto the frame support surface as
shown.
- Lock the sliding table to the frame using part A,B and C,
with 18mm wrench.
A
C
D
E
4.4.5 INSTALL TELESCOPIC FENCE
- Put the pin of telescopic fence A into the hole which is
on the outrigger.
- Lock the lock handle D for stable tighting.
A
D
Fig.4.4.5
Fig.4.4.3
A
B
C
Fig.4.4.3
4.4.2 INSTALL BLADE GUARD
Tools Required for Assembly:
-Wrench 10 mm
-Install Blade guard A to Riving knife with part 2.
Summary of Contents for Diamond 400
Page 54: ......
