background image

DANGER ZONE 

NO PERSON EXCEPT OPERATOR ALLOWED 15 METERS RADIUS DANGER ZONE. 
EYE, EAR, FACE, FOOT, LEG AND BODY PROTECTION MUST BE WORN BY 
OPERATOR. PERSONS IN ZONE OR RISK BEYOND DANGER ZONE SHOULD WEAR 
EYE PROTECTION AGAINST THROWN OBJECTS. RISK DIMINISHES WITH 
DISTANCE FROM DANGER ZONE. 

CUTTING WITH A NYLON HEAD

                                                         
                                                                                 

For nearly all cutting, it is good to 

tilt                                                                  the line head of the circle where

                                                                                 

the line is moving A W A Y you

and the debris shield.

WARNING         

DANGER

Line  head  rotates  in  a  CLOCK  WISE           

Tilting the head to the wrong side will 
shoot the debris TOWARDS you. If 
the line head is held flat to the 
ground so that cutting occurs on the 
whole line circle, debris will be 
THROWN at you, drag will slow the 
engine down, and you will use up a 
lot of line. 

direction. The CUT-OFF KNIFE will 
be on the right side of the debris 
shield.

Summary of Contents for TP425381
























Reviews: