Toshiba Tosvert-130, Installation Manual

Page: 19 / 36

18
GROUP:FUNDAMENTAL PARAMETERS #1 (Cont.)
Register Function / Title Bank Address Mask Adjustment Range Multiplier
31 ACC/DEC PATTERN #1 SELECTION 0 / 1 042D 0030 0000: Linear
0001: Self-adjusting
0002: S-Pattern #1
0003: S-Pattern #2 
32 ACCEL/DECEL PATTERN ADJUST LOW 0 / 1 04C4 00FF
0000~00032 (0 ∼ 50)
33 ACCEL/DECEL PATTERN ADJUST HIGH 0 / 1 04C5 00FF
0000~00032 (0
∼
50)
8.3.2 GROUP:FUNDAMENTAL PARAMETERS #2
Reg. Function / Title Bank Address Mask Adjustment Range Multiplier
34 BASE FREQUENCY #2 0 / 1 0432 FFFF
09C4
∼
9C40 (25.00
∼
400.00)
0.01
35 MAXIMUM OUTPUT VOLTAGE #2 0 / 1 0430 FFFF
0000
∼
0258 (0
∼
600)
1
36 VOLTAGE BOOST #2 0 / 1 042E FFFF 0000 ∼ 012C (0.0 ∼ 30.0) 0.1
37 ELECTRONIC THERMAL PROTECT LVL #2 0 / 1 0434 00FF
000A ∼ 0064 (10 ∼ 100)
1
38 STALL PROTECTION SELECTION #2 0 / 1 0437 0040 0000: ON (0)
0001: OFF (1)

39 0 STALL PROTECTION LEVEL #2 0 / 1 0435 00FF
000A
∼
00D7 (10
∼
215) 1
3A ACCELERATION TIME #2 (Ref. 1) 0 / 1 03CA FFFF
0001
∼
EA60 (0.01~ 6000)
0001
∼
EA60 (0.01~ 600)
0.1
0.01
3B DECELERATION TIME #2 0 / 1 03CC FFFF
0001
∼
EA60 (0.01~ 6000)
0001 ∼ EA60 (0.01~ 600)
0.1
0.01
3C ACC/DEC PATTERN #2 SELECTION 0 / 1 0437 0030 0000: Linear (0)
0001: Self-adjusting (1)
0002: S-Pattern #1 (2)
0003: S-Pattern #2 (3)

3D ACC/DEC #1/#2 SWITCH FREQUENCY 0 / 1 0406 FFFF
0000
∼
Fmax
0.01
8.3.3 GROUP:PANEL CONTROL PARAMETERS
Reg. Function / Title Bank Address Mask Adjustment Range Multiplier
3E DIRECTION SELECTION (FORWARD/REV) 0 / 1 04FA 0004 0000: Reverse (0)
0001: Forward (1)

3F STOP PATTERN SELECTION 0 / 1 045C 0040 0000: Decelerated stop (0)
0001: Coast stop
(1)

40 FUNDAMENTAL PARAM SWITCHING 0 / 1 04FB 0004 0000: V/F #1 (1)
0001: V/F #2 (2)

41 ACCEL/DECEL #1/#2 SELECTION 0 / 1 04FA 0008 0000: Acc / dec #1 (1)
0001: Acc / dec #2 (2) 
42 PANEL RESET SELECTION 0 / 1 045C 0030 0000: All possible (0)
0001: overload only (1)
0002: overload, overcurrent
only (2) 
43 PANEL FEEDBACK CONTROL (Note 1) 0 / 1 04FB 0001 0000: Feedback valid (0)
0001: Feedback invalid (1) 
8.3.4 GROUP:TERMINAL SELECTION PARAMETERS
Reg. Function / Title Bank Address Mask Adjustment Range Multiplier
44 INPUT TERMINAL SELECTION 0 / 1 04BB 0001 0000: Standard functions (0)
0001: Individual selection (1) 
45 1 “R” INPUT TERMINAL FUNCTION 0 / 1 046C FFFF
0000
∼
FFFF (0
∼
54) 
46 “S1” INPUT TERMINAL FUNCTION 0 / 1 046E FFFF Refer to Table 6
47 “S2” INPUT TERMINAL FUNCTION 0 / 1 0470 FFFF in RS-485 manual
48 “S3” INPUT TERMINAL FUNCTION 0 / 1 0472 FFFF
49 “S4” INPUT TERMINAL FUNCTION 0 / 1 0474 FFFF
4A “F” INPUT TERMINAL FUNCTION 0 / 1 0476 FFFF
4B “RES” INPUT TERMINAL FUNCTION 0 / 1 0478 FFFF
4C “ST” INPUT TERMINAL FUNCTION 0 / 1 047A FFFF
4D “S5” INPUT TERMINAL FUNCTION 0 / 1 047C FFFF
4E “S6” INPUT TERMINAL FUNCTION 0 / 1 047E FFFF
4F “S7” INPUT TERMINAL FUNCTION 0 / 1 0480 FFFF
50 POTENTIAL TERMINAL FUNCTION 0 / 1 0482 FFFF
51 R,S1-S7 TERMINAL RESPONSE TIME 0 / 1 0462 00FF
0001 ∼ 0064 (1 ∼ 100)
1
52 F INPUT TERMINAL RESPONSE TIME 0 / 1 0463 00FF
0001 ∼ 0064 (1 ∼ 100)
1
53 RES INPUT TERMINAL RESPONSE TIME 0 / 1 0464 00FF
0001
∼
0064 (1
∼
100)
1
54 ST INPUT TERMINAL RESPONSE TIME 0 / 1 0465 00FF
0001
∼
0064 (1
∼
100)
1