Toshiba TCB-SC640U-E Installation Manual Download | Manualshive

Page: 6 / 35

background image

Central Remote Controller

Installation Manual

6

-EN

3

Installation

3-1. Power, Signal, and Earth Line Connections

Connect the power, signal and earth lines to the specified terminal blocks.

REQUIREMENT

Attach round crimp terminals to all TU2C-LINK / TCC-LINK wiring and tighten the screws securely.
After tightening, check that the wiring cannot come out.

(1) Remove 3 cover fixing screws pointed to by arrows and open the cover
(2) Insert cross notches in the rubber bushing in order to pass the power supply cable
(3) Pass the power supply cable through the rubber bushing and the clamp, and connect the power supply wire and

the ground wire to the specified terminal block

(4) Close the cover and secure with 3 cover fixing screws

Connect the TU2C-LINK / TCC-LINK signal wire (Uh / U3U4) to the terminal block

Connect the power supply wire and the ground wire

Connect the signal wires

Cover fixing screw

Screws indicated by arrows

Cover fixing screw

Power supply cover

Rear side
terminal block

Power terminal

Power supply wire

Clamp

Ground wire

Ground terminal

Rubber bushing

(Remove the transparent
cover at installation and return
it to its original position after
connecting)

5 mm

18 mm

Termination resistance (SW1)

−

L N

COM

DI3

DI2

DI1

COM

DO2

DO1

U3

U4

TU2C-LINK / TCC-LINK does not
have polarity.
Connect the shield of the central
control wiring to the earth on the air
conditioner side.
Leave the shield open (and insulate
it). Do not connect it to the terminal
block.

Uh line
Central control wiring

Outdoor unit

Indoor unit

Remote controller

Power 220-240 V AC

Securely fix the cable with
a clamp.

«
...
4
5
6
7
8
...
»

Summary of Contents for TCB-SC640U-E




































Reviews:

No comments

Related manuals for TCB-SC640U-E

Brand: zipwake Pages: 12

Brand: Watts Pages: 2

Brand: jbc Pages: 12

Brand: Unipulse Pages: 99

Brand: Accutrol Pages: 25

Brand: Mainpine Pages: 16

Brand: Danfoss Pages: 20

Brand: Maestra Pages: 22

Brand: Lawler Pages: 4

Brand: QTP Pages: 2

PXI-6683 Series

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 29

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 7

FIELDPOINT FP-1600

Brand: National Instruments Pages: 21

FieldPoint FP-1001

Brand: National Instruments Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands