Toshiba Strata CIX40 User Manual Download Page 39

Page: 39 / 208

The Basics

Making a Call

Strata CIX IP5000-series Telephone UG 07/09

Making a Call

There are three ways to originate a call from the telephone:

Handset

1. To make a call, lift the handset, then dial the number.

A line may be automatically selected or choose a line manually. Dial tone is heard
through the handset. The Speaker and Microphone LEDs do

not

light.

Digits display as they are dialed. Call progress tones (Ringback Tone, Busy Tone,
etc.) are heard through the handset.

2. When connected, continue using the handset or switch to speakerphone by holding

down

Spkr

and placing the handset in the cradle.

Spkr Button

1. To make a call, press

Spkr

A line may be selected automatically or choose a line manually. The extension or

Line

button lights (depending on system programming). Dial tone is heard

through the speaker. The Speaker and Microphone LEDs light.

2. Dial the number.

Digits display as they are dialed. Call progress tones (Ringback Tone, Busy Tone,
etc.) are heard through the speaker.

3. When connected, continue using the speakerphone or lift the handset to continue

the conversation.

Hot Dialing

1. To make a call using Hot Dialing, start dialing the number.

The extension button, Spkr and Mic LEDs light. Digits display as they are dialed.
Call progress tones (Ringback Tone, Busy Tone, etc.) are heard through the
speaker.

2. When connected, continue using the speakerphone or lift the handset to continue

the conversation.

Summary of Contents for Strata CIX40

















































































































































































































Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands

Toshiba Strata CIX40, User Manual

Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands