Toshiba Strata CIX40 User Manual Download Page 162

Page: 162 / 208

Administrator Programming

IP5131-SDL Settings

144

Strata CIX IP5000-series Telephone UG 07/09

Port Setting

1. From the IP Configurations screen, choose Network >

> Port Setting. The Port Setting screen displays.

2. Press the Dynamic or Static softkey to change the set

value. The set value is underlined in the display.

3. Press the Set soft key to accept the change

...or press the Cancel soft key to cancel the change and
go to the Network Setting screen [2/3].

Auto Login Mode (For IP Mobility)

1. From the IP Configurations screen, choose Network >

> Auto Login Mode. The Auto Login screen

displays.

2. Press the Auto or Manual softkey to set the value. The

value set is underlined in the display.

3. Press the Set soft key to accept the change

...or press the Cancel soft key to cancel the change and
go to the Network Setting screen [2/3].

Auto Login Password

1. From the IP Configurations screen, choose Network >

> Auto Login Password. The Auto Login

Password screen displays.

2. Press the center button of the Navigation button to

highlight the field.

Using the keypad, enter the password.

3. Press the Set softkey to cancel the change and go to

the Network Setting screen [2/3].

Port Setting

Dynamic

Static

[Set]

[Cancel]

Config

Auto Login Mode

Auto

Manual

[Set]

[Cancel]

Config

Auto Login Password

Backspace = Vol-Down

[Set]

[Cancel]

Config

:Current

:New

Summary of Contents for Strata CIX40

















































































































































































































Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands

Toshiba Strata CIX40, User Manual

Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands