Toshiba Strata CIX40 User Manual Download Page 151

Page: 151 / 208

Administrator Programming

Reset Factory Default Settings

Strata CIX IP5000-series Telephone UG 07/09

133

Handset / Headset Side Tone Volume Setting

1. Press

Hold

(simultaneously).

2. Press

Redial

button.

3. Press

Hold

to access Sound Level Setting Mode.

FB03 controls Side Tone mode setting. Enter:

1 = Side Tone Off

2 = Side Tone On

FB04 controls Side Tone Volume.

Enter a value from 0dB to 12dB. Default is 0.

4. Press FBxx and enter the appropriate value.

5. Press Hold to save the settings.

6. Press Hold to return to IP Programming Mode display.

7. Lift the handset off-hook /on-hook to save settings.

LCD Contrast Setting

Available on backlit telephones.



To adjust the LCD contrast on the backlit telephones

1. Press and hold down the

Mic

button.

2. Press and release

Vol



Vol



repeatedly.

Note

Holding down the Vol key does not continue to change the setting. The key
must be pressed for each step of contrast change.



To adjust the LCD contrast on the Add-on Module

1. Press

Hold

(simultaneously).

2. Press

Contrast -

softkey / button to increase or decrease contrast.

3. Lift the handset off-hook / on-hook to save settings.

Summary of Contents for Strata CIX40

















































































































































































































Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands

Toshiba Strata CIX40, User Manual

Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands