Toshiba Strata CIX40 User Manual Download Page 175

Page: 175 / 208

Administrator Programming

IP5131-SDL Settings

Strata CIX IP5000-series Telephone UG 07/09

157

Headset Tx and Rx Volume

1. From the IP Configurations screen, select Sound >

> Handset Tx/Rx Volume. The appropriate screen will
display.

2. Enter the new volume level.

3. Press the Set soft key to accept the change.

...or press the Cancel soft key to cancel the change and
go to the Sound Setting Screen 2.

Refer to Notes section of Tx Volume for additional
details.

Side Tone Mode

1. From the IP Configurations menu, select Sound >

> Side Tone Mode. The Side Tone Mode screen

displays.

2. Press the On or Off soft keys to change the set value.

3. Press the Set soft key to accept the change.

...or press the Cancel soft key to cancel the change.

Side Tone Volume

1. From the IP Configurations menu, select Sound >

> Side Tone Volume. The Side Tone Volume screen

display.

2. Enter the new volume level.

3. Press the Set soft key to accept the change.

...or press the Cancel soft key to cancel the change and
go to the Sound Setting Screen 2.

Refer to Notes section of Tx Volume for additional
details.

Handset Tx Volume

Backspace = Vol-Down

[Set]

[Cancel]

Config

:Current

:New (-8: Min.- 6:Max)

- (Minus) = * Key

Side Tone Mode

Off

[Set]

[Cancel]

Config

Side Tone Volume

Backspace = Vol-Down

[Set]

[Cancel]

Config

:Current

:New (0: Min.- 12:Max)

- (Minus) = * Key

Summary of Contents for Strata CIX40

















































































































































































































Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands

Toshiba Strata CIX40, User Manual

Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands