– 62 –
8-2-3. Monitor Function of Remote Controller Switch
Calling of sensor temperature display
<Contents>
Each data of the remote controller, indoor unit and outdoor unit can be understood by calling the service
monitor mode from the remote controller.
<Procedure>
<Operation proced
u
re>
1 2 3 4
Ret
u
rned to
usu
al di
s
play
2
4
1
3
SET
TIME
TIMER SET
TEST
FILTER
L
RESET
TEMP.
CL
FAN
SAVE
A
SWING/FIX
VENT
MODE
ON / OFF
UNIT LOUVER
T
Indoor unit data
CODE No.
01
02
0
3
04
07
F2
F
3
F8
Data name
Room temperat
u
re
(Remote controller)
Indoor
su
ction temperat
u
re (TA)
Indoor heat exchanger (Coil)
temperat
u
re (TCJ)
Indoor heat exchanger (Coil)
temperat
u
re (TC)
Indoor fan revol
u
tion freq
u
ency
Indoor fan calc
u
lated operation time
Indoor
u
nit fan c
u
m
u
lative operating ho
u
r
s
Indoor di
s
charge temperat
u
re
Unit
˚C
˚C
˚C
˚C
rpm
×100h
×1h
˚C
Outdoor unit data
CODE No.
60
61
62
6
3
65
6A
6D
70
72
7
3
F1
Data name
O
u
tdoor heat exchanger (Coil) temperat
u
re (TE)
O
u
t
s
ide temperat
u
re (TO)
Compre
ss
or di
s
charge temperat
u
re (TD)
Compre
ss
or
su
ction temperat
u
re (TS)
Heat
s
ink temperat
u
re (THS)
Operation c
u
rrent (× 1/10)
O
u
tdoor heat exchanger (Coil) temperat
u
re (TL)
Compre
ss
or operation freq
u
ency
O
u
tdoor fan revol
u
tion freq
u
ency (Lower)
O
u
tdoor fan revol
u
tion freq
u
ency (Upper)
Compre
ss
or calc
u
lated operation time
Unit
˚C
˚C
˚C
˚C
˚C
A
˚C
rp
s
rpm
rpm
×100h
1
Push + buttons simultaneously for 4 seconds to
call the service monitor mode.
The service monitor goes on, the header indoor unit No. is
displayed at first and then the temperature of CODE No.
00
is
displayed.
Ø
2
Push temperature set
buttons and then change
the CODE No. of data to be monitored.
The CODE No. list is shown below.
Ø
3
Push
UNIT LOUVER
button to select the indoor unit to be monitored.
Each data of the indoor unit and its outdoor units can be monitored.
Ø
4
Pushing button returns the status to the usual display.
∗
1 The indoor discharge temperature of CODE No. [F8] is the estimated value from TC or TCJ sensor.
Use this value to check discharge temperature at test run.
(A discharge temperature sensor is not provided to this model.)
• The data value of each item is not the real time, but value delayed by a few seconds to ten-odd seconds.
Summary of Contents for RAV-GM 1101UT-E
Page 30: ... 30 2 CONSTRUCTION VIEWS EXTERNAL VIEWS 2 1 RAV GP801AT ...
Page 31: ... 31 2 2 RAV GP1101AT GP1401AT ...
Page 36: ... 36 4 WIRING DIAGRAM 4 1 RAV GP801AT 220 240V 50Hz P 3 3 Fuse 25A 250V Fuse 10A 250V ...
Page 37: ... 37 4 2 RAV GP1101AT GP1401AT 220 240V 50Hz P 3 3 3 Fuse 25A 250V Fuse 10A 250V ...
