– 116 –
No. Part name
Procedure
Remarks
i
Compressor
and
compressor
lead
WARNING
When removing the welding part of the suction / discharge
pipe of the compressor, remove them after recovering the
refrigerant in a well-ventilated place. if recovery is
insufficient the refrigerant and refrigerating machine oil
may squirt, cause injury.
1) Recover refrigerant gas.
2) Following to work of Detachment of
c
and
f
.
3) Remove the piping panel (front).
Remove the screws from piping panel (front) and base
plate. (2 pcs, Ø4 × 10 hexagon screws)
Remove the screws from the piping panel (front) and
piping panel (rear).
(1 pcs, Ø4 × 10 hexagon screw)
4) Remove the piping panel (rear). Remove the screws on
the piping panel (rear) and the bottom plate.
(2 pcs, Ø4×10 hexagon screws)
5) Remove the valve fixing plate
Remove the screws for the valve fixing plate
Remove 2 bolts for liquid valve side and valve fixing
plate. (2 pcs DELTITE screw M6 ×15)
Remove 2 bolts for gas valve side and valve fixing
plate. (2 pcs DELTITE screw M6 ×15)
6) Remove the pipe cover and TD sensor fixing the
discharge pipe
7) Remove the sound insulation board (upper, inner, and
outer).
8) Remove the compressor’ terminal cover (2 claws) and
compressor lead and compressor case thermostat(
one claw).
9) Cut the binding band fixing the inverter box (2 positions)
and the other binding band rolled around the compressor
lead.
10) Remove the connector for the compressor lead to
remove the compressor lead.(Keep the ferrite core
attached to the electric parts box.)
11) Remove the discharge and suction pipes connected
to the compressor using a burner.
WARNING
Ensure extreme caution when removing piping by melting
the weld with a burner as fire may result if there is any oil
within the piping.
NOTE
Carefully avoid contact with the 4-way valve and PMV with
the flame (could result in a malfunction).
12) Remove the refrigeration cycle discharge and suction
pipes by pulling them upwards.
13) Remove the compressor nuts securing the
compressor to the base plate. (H13 × 3 nuts)
14) Pull the compressor forwards.
NOTE
The compressor weighs at least 15kg. Ensure two people
carry out the work.
Pipe p
a
nel (front))
Pipe p
a
nel (front))
Pipe p
a
nel (re
a
r)
Pipe p
a
nel (re
a
r)
Ø4 screws
Ø4 screws
Disch
a
rge pipe
Disch
a
rge pipe
TD sensor
TD sensor
S
crew
S
crew
S
crew
S
oundproof pl
a
te(outer)
Termin
a
l cover
Termin
a
l cover
Pipe cover
Pipe cover
S
crew
Compressor le
a
d
Compressor le
a
d
(Red • White • Bl
a
ck)
(Red • White • Bl
a
ck)
Disch
a
rge pipe
Disch
a
rge pipe
(Remove here)
(Remove here)
S
uction pipe
S
uction pipe
(Remove here)
(Remove here)
46
8
Compressor le
a
d
b
inding
ba
nd
Compressor le
a
d
Binding
ba
nd fixing inverter
b
ox
(2 positions)
Compressor c
a
se
Compressor c
a
se
thermost
a
t
thermost
a
t
Pipe p
a
nel (front))
Pipe p
a
nel (re
a
r)
Ø4 screws
S
ound prof p
a
nel(Upper)
DELTITE screw
DELTITE screw
Li
q
uid side v
a
lve
Li
q
uid side v
a
lve
G
a
s side v
a
lve
G
a
s side v
a
lve
Compressor le
a
d
(Red • White • Bl
a
ck)
Disch
a
rge pipe
(Remove here)
S
uction pipe
(Remove here)
Compressor
b
olts
Compressor
b
olts
(H13 × 3 positons)
(H13 × 3 positons)
Compressor c
a
se
thermost
a
t
Li
q
uid side v
a
lve
G
a
s side v
a
lve
DELTITE screw
S
oundproof pl
a
te(inner)
S
oundproof pl
a
te(inner)
Disch
a
rge pipe
TD sensor
S
crew
Termin
a
l cover
Pipe cover
S
oundproof pl
a
te(inner)
Compressor
b
olts
(H13 × 3 positons)
Summary of Contents for RAV-GM 1101UT-E
Page 30: ... 30 2 CONSTRUCTION VIEWS EXTERNAL VIEWS 2 1 RAV GP801AT ...
Page 31: ... 31 2 2 RAV GP1101AT GP1401AT ...
Page 36: ... 36 4 WIRING DIAGRAM 4 1 RAV GP801AT 220 240V 50Hz P 3 3 Fuse 25A 250V Fuse 10A 250V ...
Page 37: ... 37 4 2 RAV GP1101AT GP1401AT 220 240V 50Hz P 3 3 3 Fuse 25A 250V Fuse 10A 250V ...
