- 37 -
NO.
KEY SWITCH
OUTLINE OF SPECIFICATIONS
REMARKS
6.2 Outline of remote controller's functions
1
[ON/OFF]
À
When this button is pushed once, the air conditioner is turned on, with the operation
lamp coming on.
Á
If pushed once more, it will be turned off, the operation lamp going off.
Â
If pushed for 5 sec. in the mode of turning on the air conditioner, goes into test run
mode.
2
À
Each time this button is pushed, the [MODE] setting is changed over cyclically,
[COOL]
→
[FAN ONLY]
→
[COOL].
Á
If pushed continuously, the setting will be changed in one step every 0.5 sec.
MODE
SELECT
3
À
Each time this button is pushed, the [FAN] setting is changed over cyclically,
[AUTO]
→
[LOW]
→
[MED]
→
[HIGH]
→
[AUTO].
Á
If pushed continuously, the setting will be changed in one step every 0.5 sec.
Fan speed
4
À
Each time [ + ] button is pushed, the [TEMP] setting of temperature is raised by
1
°
C.
Á
If [ + ] is pushed continuously, the setting will be raised by 1
°
C every 0.5 sec.
Â
Each time [ - ] button is pushed, the setting of temperature is lowered by 1
°
C.
¯
If [ - ] is pushed continuously, the setting will be lowered by 1
°
C every 0.5 sec.
In the 18 ~ 29
°
Control range
5
À
Each time [TIME ADJUST] button is pushed, the [TIME] display is changed
cyclically. The time can be changed while the TIME display stays flashing.
(flashing)
(flashing)
(flashing)
[CLOCK]
→
[CLOCK]
→
[ON TIME]
→
[OFF TIME]
[12:00]
[12:00]
[6:00]
[18:00].
Á
While the TIME display stays flashing, the time gains one minute upon each
pressing of [ + ].
Â
If [ + ] is pushed continuously, the time gains 10 minutes every 0.25 sec.
¯
While the TIME display stays flashing, the time goes back one minute upon each
pressing of [ – ].
Ä
If [ – ] is pushed continuously, the time goes back 10 minutes every 0.25 sec.
6
Each time [TIMER SELECT] button is pushed, timer mode change over cyclically,
[
] (CONTINUE)
→
[ON]
→
[OFF]
→
[ON
→
OFF]
→
[ON
←
OFF]
→
[CYCLE]
→
[
].
7
If pushed continuously, the timer mode will be changed in one step every 0.5 sec.
If time is not set,
12:00
6:00
18:00
are set
automatically
TIME
ADJUST
+
–
TIME
ADJUST
6
À
Pressing this key for 0.5 sec. provides [MALFUNCTION CHECK], indicating on
liquid crystal the contents of inspection in the sequence of (times of compressor -
on)
Þ
(contents of malfunction for # 1 unit)
Þ
(contents of malfunction for # 2
unit)
Þ
....
Á
Pressing this key for 5 sec. gives "Indoor microcomputer reset mode" to reset the
indoor microcomputer by way of hardware.
Â
Pressing this key for 10 sec. gives "Check contents clear mode" to clear the contents
of inspection stored in the remote controller provided, however, times of
compressor-on is not cleared.
CHECK
7
Reset
À
By pressing the reset key, the remote controller is reset by way of hardware.
(The setting/display are in initial values with the check memory cleared.)
The indication of
the indoor unit
which has not any
malfunction content
is skipped.
+
–
Heronhill - for all your Toshiba requirements
Tel: 01823 665660
www.heronhill.co.uk
Fax: 01823 665807
