manualshive.com logo in svg

Toshiba PNE001Z, Function Manual

Share
Download
Toshiba PNE001Z Function Manual Download Page 63

 

E6582051 

- 60 - 

9. Specifications 

 

Module specifications 

Item Specification 

Type-form PNE001Z 

Applicable inverter 

VF-S15 CPU1 Ver.112 or later (With SBP009Z) 

Connector 

Dual RJ45 shielded connector 

Supported network 

PROFINET, Modbus TCP 

Indicator 

4 LEDs indicating the communication status and error 
status. 

Protection degree 

IP20 

Environments 

Correspond to inverter. 

 

Network specifications 

Item Specification 

PROFINET 

Baud rate 

100Mbps (Full duplex) 

Cyclic communication 

PROFIdrive V.4.1

 

(Telegram1) 

4PKW and 2 PZD vendor format (Telegram100) 
4PKW and 6 PZD vendor format

 

(Telegram101) 

6 PZD vendor format

 

(Telegram102) 

Acyclic communication 

Reading the PROFIdrive parameter 
Reading/writing the inverter parameters 

Configuration 

Configure by PROFINET master 

IP configuration mode 

Manual setup, DCP, DHCP, Embedded Web server 

PROFINET IO classes 

Conformance Class-B 

I&M 

I&M function 0 

Modbus TCP 

Baud rate 

10/100Mbps (Full/Half duplex) 

Supported function 

Read Holding Registers (03H)   
Write Single Register (06H) 
Write Multiple Registers (10H) 
Read Device Identification (2BH) 

IP configuration mode 

Manual setup, DHCP, Embedded Web server 

Ethernet 

MRP Supported 
LLDP Supported 

Web server 

Inverter status monitor, inverter parameter 
monitor/configuration, Network status monitor, 
password lock 

 
 

 

Summary of Contents for PNE001Z
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands