Toshiba E-Studio167 Page 58 Operator'S Manual Download | Manualshive

Page: 58 / 226

background image

2 HOW TO MAKE COPIES

56 Placing Originals

The following types of originals are usable but need extra care:

y

Ones which cannot be made to slide with the fingers or whose surface is specially treated
(they may not be able to be separated from each other at feeding)

y

Folded or curled ones (should be smoothed out before being used)

When black streaks appear on the copied image

If the scanning area or the guide area is dirty, image problems such as black streaks on the cop-
ied image may occur. Weekly cleaning of these areas is recommended.

P.202 “Daily Inspection”

Placing originals on Reversing Automatic Document Feeder (optional)
/ Automatic Document Feeder (optional)

1

Align all the originals.

2

Place them face up and align the side guides to the original length.

y

The top sheet of the originals will be scanned first.

y

The total sheets of originals placed must not exceed 100 (13.3 to 20 lb.) or the stack
height of the originals must not exceed 0.62" regardless of their sizes.

When placing a large amount of originals with a long width

Pull out the original stopper so that the exiting originals will not fall. When replacing this
stopper, lift it slightly and push it in.

«
...
56
57
58
59
60
...
»

Summary of Contents for E-Studio167



































































































































































































































Reviews:

No comments

Related manuals for E-Studio167

Brand: Xerox Pages: 34

Brand: Xerox Pages: 192

Brand: F+D Feinwerk- und Drucktechnik Pages: 41

Brand: EBS Pages: 34

ESP 3200 Series

Brand: Kodak Pages: 90

Brand: Olivetti Pages: 8

Brand: Canon Pages: 8

Brand: Canon Pages: 58

Brand: Canon Pages: 110

MultiPASS MP360

Brand: Canon Pages: 162

Brand: Canon Pages: 200

Brand: Canon Pages: 58

Brand: Canon Pages: 184

Brand: Canon Pages: 236

Brand: Canon Pages: 996

Brand: Canon Pages: 9

Brand: MUTOH Pages: 16

Brand: MUTOH Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands