Toshiba E-Studio167 Page 21 Operator'S Manual Download | Manualshive

Page: 21 / 226

background image

General Precautions 19

General Precautions

When installing or moving

Warning

y

This equipment requires 115 V, 12 A, 50/60 Hz electric power.
Do not use a power supply with a voltage other than that specified.
Avoid multiple connections in the same outlet. This could cause a fire or give you an electric
shock. If you are considering increasing the number of outlets, contact an electrician.

y

Always connect this equipment to an outlet with a ground connection to avoid the danger of
fire or electric shock in case of short-circuiting. Contact your service representative for the
details. Be sure to use a 3-conductor, grounded wall outlet.
In areas, except the U.S. and Canada, where a 2-pin plug is used, the equipment must be
grounded for safety. Never ground it to a gas pipe, a water pipe, or any other object not suit-
able for grounding.

y

Plug the power cable securely into the outlet. If it is not plugged in properly, it could heat up
and cause a fire or give you an electric shock.

y

Do not damage, break or attempt to repair the power cable.
The following things should not be done to the power cable.

- Twisting it
- Bending it
- Pulling it
- Placing anything on it
- Making it hot
- Situating it near radiators or other heat sources

This could cause a fire or give you an electric shock. If the power cable is damaged, contact
your service representative.

y

Do not install the equipment by yourself or try to move it once it has been installed. This
could result in an injury or damage to the device. Contact your service representative if the
equipment needs to be installed or moved.

y

Pull the plug out from the outlet more than once a year to clean around the prongs. Accumu-
lating dust and dirt could cause a fire due to the heat released by electric leakage.

«
...
19
20
21
22
23
...
»

Summary of Contents for E-Studio167



































































































































































































































Reviews:

No comments

Related manuals for E-Studio167

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 858

SPP 2020 - Photo Printer - 20 Sheets

Brand: Samsung Pages: 81

Brand: Samsung Pages: 98

Brand: Samsung Pages: 6

Brand: Samsung Pages: 203

Brand: Samsung Pages: 264

Brand: Samsung Pages: 228

Brand: Samsung Pages: 211

Brand: Samsung Pages: 5

Brand: Samsung Pages: 92

Brand: Samsung Pages: 75

Brand: Samsung Pages: 11

Brand: Samsung Pages: 206

ML 3050 - B/W Laser Printer

Brand: Samsung Pages: 103

ML 3050 - B/W Laser Printer

Brand: Samsung Pages: 215

Brand: Samsung Pages: 2

CLP 510N - Color Laser Printer

Brand: Samsung Pages: 266

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands