Toshiba DVS32-240-2T Software Manual Download Page 74

Page: 74 / 105

ADVANCED PTZ SETUP

Note

Preset and Tour options may vary depending on the camera

Creating and Viewing Preset Positions

A Preset Position is a user-defined location where the camera can be pointed, zoomed in, and focused. Preset positions can be
defined and labeled if the camera supports this.

Creating a Preset

Inside Setup, click PTZ and select the camera.

If the camera is already selected click Open PTZ Controller.

Move the selected camera to the desired position using the Pan/Tilt/Zoom/Focus controls.

In the Preset & Tour Detail section, choose a Preset # (1-10)
using the list or the Right and Left Arrow buttons and click Select.

Note

Preset positions can also be created using the advanced buttons on the PTZ graphical controller.

Viewing a Preset

From the Display screen select the PTZ camera by clicking on it.

Using the keyboard click the number keys corresponding with the Preset Positions. The camera will move to the saved Preset.

Adjust Speed Settings

PTZ signal type

Connection Settings

Summary of Contents for DVS32-240-2T










































































































Search results

Summary of Contents for DVS32-240-2T

Reviews:

Related manuals for DVS32-240-2T

Brands by name

Popular brands

Toshiba DVS32-240-2T, Software Manual

Search results

Summary of Contents for DVS32-240-2T

Reviews:

Related manuals for DVS32-240-2T

Brands by name

Popular brands