Toshiba Copier Operator'S Manual Download Page 65 | Manualshive

Page: 65 / 78

background image

TROUBLESHOOTING

5-1

Problem

Check and Remedy

Dialing cannot be done.

Make sure that the telephone line is
properly connected to both the unit and
the wall jack.

No transmission takes place.

Make sure that the receiving machine has
not run out of printing paper.
Make sure that the receiving machine is
G3 compatible. (This information should
be included in the machine’s
documentation.)
Check the display for possible error
messages.

Nothing is printed at the receiving end.

Make sure that the document you are
sending is fed into the unit in the correct way.
Make sure that the receiving machine is
in working order.

A distorted image is received at the other end.

Noise on the telephone line may cause
distortion. Try sending the document again.
Make a copy of the document on the unit.
If the copy is also distorted, the unit may
have a problem.

The received document is faint.

Ask the other party to send higher contrast

documents. If the contrast is still too low,
make a copy with the unit to check it.

Received images are distorted.

Noise on the telephone line may cause
distortion. Have the sending party send
the document again.
The drum car tridge may need
replacement.

COPY SERVICE ERROR

The copier will not function. Turn the power

switch off, remove the power cord from
the outlet, and contact your TOSHIBA
dealer.

FAX SERVICE ERROR (X)

The fax will not function.Contact your
TOSHIBA dealer.

Note: If your problem cannot be solved by carrying out the instructions in the Check

and Remedy column above, please contact your TOSHIBA dealer.

5. TROUBLESHOOTING

Troubleshooting

«
...
63
64
65
66
67
...
»

Summary of Contents for Copier















































































Reviews:

No comments

Related manuals for Copier

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 4

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 16

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 170

Brand: Samsung Pages: 165

Brand: Xerox Pages: 114

Brand: Chamjin I&C Pages: 21

Brand: Xerox Pages: 93

Brand: Xerox Pages: 36

Copycentre C118

Brand: Xerox Pages: 12

Brand: Xerox Pages: 136

4250 - WorkCentre - Copier

Brand: Xerox Pages: 4

4250 - WorkCentre - Copier

Brand: Xerox Pages: 4

Brand: Xerox Pages: 8

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 4

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 40

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 38

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 201

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands