Toshiba BU406M Instruction Manual Download Page 43

Page: 43 / 67

42 / 65

D4223121B

www.toshiba-teli.co.jp

TriggerControl

This section describes trigger control of TriggerControl category.

This camera provides two kinds of exposure synchronization.

1. Normal Shutter mode

: Free run operation (internal synchronization)

2. Random Trigger Shutter mode : Synchronized with external trigger input

In Random Trigger Shutter mode, two kinds of trigger input are available.

1. Trigger signal via the I/O connector (HardwareTrigger)

2. Trigger command via the USB interface (SoftwareTrigger)

The following table shows the combination of operation mode.

Table. Operation Mode

Trigger Mode

Synchronization

Exposure Control

Normal Shutter mode

Free run

“ExposureTime” register control

Random Trigger Shutter mode

HardwareTrigger

-Edge mode:TriggerSequence0

-Bulk mode:TriggerSequence6

“ExposureTime” register control

-Level mode:TriggerSequence1

Trigger pulse width control

SoftwareTrigger

-Edge mode:TriggerSequence0

-Bulk mode:TriggerSequence6

“ExposureTime” register control

* The camera operation not mentioned above is not guaranteed.

Summary of Contents for BU406M



































































Search results

Summary of Contents for BU406M

Reviews:

Related manuals for BU406M

Brands by name

Popular brands

Toshiba BU406M, Instruction Manual

Search results

Summary of Contents for BU406M

Reviews:

Related manuals for BU406M

Brands by name

Popular brands