Toshiba BU406M Instruction Manual Download Page 16

Page: 16 / 67

15 / 65

D4223121B

www.toshiba-teli.co.jp

Connection

Notes on Connection:

- Please confirm the power supply of the camera off when plugging in or pulling out the I/O Connector. It causes the

breakdown.

- If your camera is used in a system where its connectors are subjected to strong repetitive shocks, its connectors are

possible to break down. If you use your camera in such a situation, use an USB3.0 cable with a lock screw, and secure

the camera cable as close as possible to the camera body for avoid physical shock to the camera connector.

- About e-CON cable: In the case that electric-wire is long or thin, input and output voltage may not satisfy specifications

of the camera or your system by voltage drop. Please confirm wires’ specifications before use them.

Lost packets may occur by an electrical characteristic of the transmission line of USB3.0. (USB3.0 Interface Card,

USB3.0 Cable, and USB3.0 HUB).

Summary of Contents for BU406M



































































Search results

Summary of Contents for BU406M

Reviews:

Related manuals for BU406M

Brands by name

Popular brands

Toshiba BU406M, Instruction Manual

Search results

Summary of Contents for BU406M

Reviews:

Related manuals for BU406M

Brands by name

Popular brands