manualshive.com logo in svg

Toshiba A60 S1591 - Satellite - Celeron D 2.8 GHz, Maintenance Manual

Share
Download
Toshiba A60 S1591 - Satellite - Celeron D 2.8 GHz Maintenance Manual Download Page 199

4.16 LCD Module

 

4 Replacement Procedure

s 

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

 

4

-

55

 

Installing the 15.0-inch LCD Module 

NOTE: 

LCD/FL cable must be carefully peeled away before disconnecting it from the 

module. 

 

Install the 15.0-inch LCD module according to the following procedures and Figures 4-35, 4-36 
and 4-37.  

1.

 

Turn the LCD upside down. 

2.

 

Connect the LCD/FL cable to the LCD module then stick tape for securing the LCD 
connector. 

3.

 

Return the normal LCD placement. 

4.

 

Place the LCD bracket in the correct position and secure it with the three M2x3 black bind 
screws on each of the left and right sides. 

5.

 

Place the LCD module in the correct position and secure it with the two M2.5x4.5 black 
flat-head screws and two M2x5 white bind screws. 

Summary of Contents for A60 S1591 - Satellite - Celeron D 2.8 GHz







































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands