manualshive.com logo in svg

Toshiba A60 S1591 - Satellite - Celeron D 2.8 GHz, Maintenance Manual

The Toshiba A60 S1591 - Satellite - Celeron D 2.8 GHz is a reliable and efficient laptop designed to meet your everyday computing needs. To ensure optimal performance and longevity, it is essential to follow the guidelines mentioned in the Maintenance Manual. You can easily download this manual for free from manualshive.com, where comprehensive user guides are available for instant download.

Share
Download
background image

4.3 HDD

 

4  Replacement Procedures

 

Equium A60/ Satellite A60/ Pro A60/ A65

 

Maintenance Manual

 

4-21

 

HDD pack

 

Figure 4-11  Removing the HDD pack 

4.

 

Remove the HDD pack by pulling the HDD tap attached to the HDD pack. 

 

NOTE: 

 Do not disassemble the HDD pack when it is working normally.  Disassemble or 

replace the HDD pack only if it failed. 

5.

 

Place the HDD pack on a flat surface (such as a desk), and remove the two M3x4 black 
flat-head screws. 

6.

 

Remove the HDD bracket.  

M3x4 black flat-head screw 

HDD bracket

HDD

 

Figure 4-12  Removing the HDD chassis 

CAUTION

:  Do not apply pressure to the top or bottom of the drive. 

Summary of Contents for A60 S1591 - Satellite - Celeron D 2.8 GHz







































































































































































































































































Reviews:

No comments

Related manuals for A60 S1591 - Satellite - Celeron D 2.8 GHz

IBM ThinkPad 770X Supplementary Manual preview
ThinkPad 770X
Brand: IBM Pages: 2
IBM ThinkPad 560Z User Manual preview
ThinkPad 560Z
Brand: IBM Pages: 189
IBM ThinkPad 600 Reference Manual preview
ThinkPad 600
Brand: IBM Pages: 147
Panasonic The Toughbook 31 Features preview
The Toughbook 31
Brand: Panasonic Pages: 2
Panasonic The Toughbook 31 Specification preview
The Toughbook 31
Brand: Panasonic Pages: 2
Panasonic The Toughbook 31 Operating Instructions Manual preview
The Toughbook 31
Brand: Panasonic Pages: 40
Radio Shack TRS-80 Model 100 Quick Reference Manual preview
TRS-80 Model 100
Brand: Radio Shack Pages: 28
Radio Shack TRS-80 Model 100 User Manual preview
TRS-80 Model 100
Brand: Radio Shack Pages: 230
IBM THINKPAD T43P Install Manual preview
THINKPAD T43P
Brand: IBM Pages: 2
Gigabyte innote Q1580M User Manual preview
innote Q1580M
Brand: Gigabyte Pages: 387
Acer eMachines E720 Series Service Manual preview
eMachines E720 Series
Brand: Acer Pages: 214
Acer eMachines E730 Series Quick Manual preview
eMachines E730 Series
Brand: Acer Pages: 314
Acer Extensa 15 EX215 User Manual preview
Extensa 15 EX215
Brand: Acer Pages: 81
Acer TravelMate 660 series Manual Do Utilizador preview
TravelMate 660 series
Brand: Acer Pages: 98
Acer TravelMate 650 Series Manual Do Utilizador preview
TravelMate 650 Series
Brand: Acer Pages: 98
Huawei 1174092 Quick Start Manual preview
1174092
Brand: Huawei Pages: 120
Dell Inspiron 14Z 5423 Owner'S Manual preview
Inspiron 14Z 5423
Brand: Dell Pages: 94
Philips SLE3400FN/10 Datasheet preview
SLE3400FN/10
Brand: Philips Pages: 1

Brands by name

Popular brands

Load more brands