manualshive.com logo in svg

TOSHIBA TEC Corporation B-FP Series, Manual, Page: 13 / 124

Share
Download
TOSHIBA TEC Corporation B-FP Series Manual Download Page 13

 

-7- 

Cover open 

（

ON LINE

）

 

 

 
←M

essage

 

 

← Message

 

 

 

Setting 
mode 

 

 

 

← Icon

 

 

← Message

 

 

← Model name, Firmware version (*1)

 

 

*About  image  in  User  System  Mode,  Refer  to  [6  DISPLAY  PATTERN  AND  KEY  OPERATION  FOR  SYS
TEM  MODE  AND  USER  MODE] 
*About  icon,  Refer  to  [5.5.2  Icon] 
 

（

*1

）

The  model  name  description 

BFP  3  D     

 

Print  method     D:  Direct  thermal   
Print  width     

3”  width 

Series model 
 

V  1  .  0  x     

 

revision  up:  SP,  A-Z,  a-z  (Modify  problem) 
minor  version  0-9  (Spec  change) 
Major  version  1-9  (Spec  change  about  hardware  difference) 
Firmware  version:  V 

 
(*2)  The  remaining  label  description 

 

TO DO:    0005   

 
 

  

 

          The number of remaining labels to print 

 
[The  number  of  remaining  labels  to  print]  =  [Specified  number  of  labels  to  print] 

– [The number of normally printed 

labels before occurrence of an error or placing the printer in pause] 

When the number of remaining labels to print is zero, it is not displayed.   

 

Summary of Contents for B-FP Series





























































































































Reviews:

No comments