Torque Fitness TQ5-001 Assembly And Maintenance Manual Download

Page: 34 / 46

Page

STEP

IMPORTANT!

Recheck that all frame connections and
cables are secure and check every pulley
location to make sure cable is not rubbing
on any cable retaining bracket.

TO ADD/REDUCE CABLE TENSION

Insert the

TORQUE FORK

(62) into the

tenth WEIGHT PLATE (60 and perform 10
repititions at each station. This will help re-
move most of the initial stretch in the
CABLES.

Adjust the tension in the cables by tightening
or loosening the threaded ends of the cables
at the cable adjustment points as shown.

(NOTE: The jam nuts will need to be loos-
ened in order to do this and will need to be
retightened when complete.)

STOP!

Prior to next steps (Shroud Assembly),
ensure all exercises are smooth. If rough
or loud recheck cable routing.

If GUIDE RODS have not been lubricated
refer to STEP 16.

CABLE

ADJUSTMENT

POINT

CABLE

ADJUSTMENT

POINT

LUBRICATE

GUIDE

RODS

Summary of Contents for TQ5-001















































Search results

Summary of Contents for TQ5-001

Reviews:

Related manuals for TQ5-001

Brands by name

Popular brands

Torque Fitness TQ5-001, Assembly And Maintenance Manual

Search results

Summary of Contents for TQ5-001

Reviews:

Related manuals for TQ5-001

Brands by name

Popular brands