Torque Fitness TQ5-001 Assembly And Maintenance Manual Download

Page: 31 / 46

Page

STEP

NOTE: The cable routing for each HIGH-
MID PULLEY CABLE (67) is the same on
both sides of the machine.

Holding the cable end parallel with the floor
and with the bolts facing up and down, carefully
remove the bolts from the

FAST ATTACH

CABLE COUPLER on the HIGH-MID PULLEY
CABLE (67) as shown.

Slide the HOUSING away from the SLIDE and
remove the ball end of the cable from the
COUPLER CORE. Slide HOUSING off of the
CABLE.

(NOTE: the

FAST ATTACH

CABLE COUPLER will be re-assembled in a
later step.)

Route the ball end of the HIGH-MID PULLEY
CABLE (67) around the V-GROOVE PULLEY
in the MID SWIVEL PULLEY (23), thru the
PIVOT ARM (21) and around the 4-1/2” PUL-
LEY in the MID PULLEY ARM PIVOT (16) as
shown.

Route the ball end of the HIGH-MID PULLEY
CABLE (67) around the 4-1/2” PULLEY on the
BASE (2) as shown.

Make sure the cable runs in the groove of
the pulleys and under the retaining pins.

BOLT

ROLLER

COUPLER

CORE

SLIDE

HOUSING

SPRING

NOTE: CABLE
MUST RUN
UNDER CABLE
RETAINING
PIN

Summary of Contents for TQ5-001















































Search results

Summary of Contents for TQ5-001

Reviews:

Related manuals for TQ5-001

Brands by name

Popular brands

Torque Fitness TQ5-001, Assembly And Maintenance Manual

Search results

Summary of Contents for TQ5-001

Reviews:

Related manuals for TQ5-001

Brands by name

Popular brands