Toro Z580-D Z Master 74266 Operator'S Manual Download Page 20

Page: 20 / 68

Figure 11

Warning— wear hearing protection

Operating the Parking Brake

Always set the parking brake when you stop the
machine or leave it unattended.

Setting the Parking Brake

1. Move the motion control levers (Figure 18) out to

the neutral lock position.

2. Pull up and back on the parking brake lever to set

the parking brake (Figure 12). The parking brake
lever should stay firmly in the engaged position.

WARNING

Parking brake may not hold machine parked
on a slope and could cause personal injury or
property damage.

Do not park on slopes unless wheels are
chocked or blocked

Releasing the Parking Brake

Push forward and down on the parking brake lever
to release the parking brake (Figure 12). The parking
brake is disengaged and the lever will rest against the
brake stop.

Figure 12

Parking brake-ON

Brake Stop

Parking brake-OFF

Starting and Stopping the
Engine

Starting the Engine in Normal Weather

1. Raise the ROPS up and lock into place, sit on the

seat and fasten the seat belt.

2. Move the motion controls to the neutral locked

position.

3. Set the parking brake; refer to Setting the Parking

Brake.

4. Move the PTO (power take off) switch to the off

position (Figure 13).

5. Move the throttle lever to the middle position

(Figure 15).

6. Turn the ignition key clockwise to the run position

(Figure 14).

7. Push the glow plug switch for 10 seconds. The light

will turn on.

8. Release the switch after 10 seconds. The light will

turn off.

Summary of Contents for Z580-D Z Master 74266





































































Search results

Summary of Contents for Z580-D Z Master 74266

Reviews:

Related manuals for Z580-D Z Master 74266

Brands by name

Popular brands

Toro Z580-D Z Master 74266, Operator'S Manual

Search results

Summary of Contents for Z580-D Z Master 74266

Reviews:

Related manuals for Z580-D Z Master 74266

Brands by name

Popular brands