Toro TimeCutter ZS 3200S Operator'S Manual Download Page 3

Page: 3 / 56

Contents

Safety ........................................................................... 4

Safe Operating Practices........................................... 4
Toro Mower Safety .................................................. 6
Model 74650........................................................... 7
Model 74655........................................................... 7
Slope Indicator ....................................................... 8
Safety and Instructional Decals ................................. 9

Product Overview .........................................................13

Controls ...............................................................13

Operation ....................................................................15

cm (32-inch) decks) .............................................22

Converting to Side Discharge (for models with 107

cm (42-inch) decks) .............................................23

Transporting the Machine........................................24
Loading the Machine ..............................................25
Operating Tips ......................................................26

Maintenance .................................................................27

Recommended Maintenance Schedule(s) ......................27
Premaintenance Procedures ........................................28

Raising the Seat ......................................................28
Releasing the Mower-Deck Curtain ...........................28

Lubrication ...............................................................28

Greasing the Bearings .............................................28

Engine Maintenance ..................................................29

Servicing the Air Cleaner .........................................29
Servicing the Engine Oil..........................................30
Servicing the Spark Plug ..........................................33
Cleaning the Blower Housing ...................................33

Fuel System Maintenance ...........................................34

Replacing the In-Line Fuel Filter...............................34

Electrical System Maintenance ....................................35

Charging the Battery ...............................................35
Servicing the Fuses .................................................37

Drive System Maintenance .........................................37

Checking the Tire Pressure ......................................37
Releasing the Electric Brake .....................................38

Mower Maintenance ...................................................38

Servicing the Cutting Blades.....................................38
Leveling the Mower Deck ........................................41
Removing the Mower..............................................43
Installing the Mower ...............................................44
Replacing the Grass Deflector ..................................44

Mower Belt Maintenance ............................................45

Servicing the Mower Belt.........................................45

Cleaning ...................................................................47

Washing the Underside of the Mower ........................47

Storage ........................................................................48

Cleaning and Storing the Machine .............................48

Troubleshooting ...........................................................49
Schematics ...................................................................51

Summary of Contents for TimeCutter ZS 3200S

























































Search results

Summary of Contents for TimeCutter ZS 3200S

Reviews:

Brands by name

Popular brands

Toro TimeCutter ZS 3200S, Operator'S Manual

Search results

Summary of Contents for TimeCutter ZS 3200S

Reviews:

Brands by name

Popular brands