manualshive.com logo in svg

Toro TimeCutter ZS 3200S, Operator'S Manual

Share
Download
Toro TimeCutter ZS 3200S Operator'S Manual Download Page 12

132-0869

1.

Warning—read the

Operator's Manual

.

3.

Cutting hazard of hand,
mower blade; pinching
hazard of hand, belt—keep
hands and feet away from
moving parts; keep all
guards and shields in place.

5.

Ramp tipping
hazard—when loading
onto a trailer, do not use
dual ramps; only use a
single ramp wide enough
for the machine and that
has an incline less than
15 degrees; back up the
ramp (in reverse) and drive
forward off the ramp.

7.

Tipping hazard on
slopes—do not use on
slopes near open water; do
not use on slopes greater
than 15 degrees.

2.

Warning—before servicing,
engage the parking brake,
remove the key and the
spark plug connection.

4.

Thrown object
hazard—keep bystanders
away from the machine;
remove debris from the
area before mowing; keep
the deflector shield down.

6.

Bodily harm hazard—no
riders; look behind you
when mowing in reverse.

12

 

Summary of Contents for TimeCutter ZS 3200S

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands