manualshive.com logo in svg

Toro TimeCutter ZS 3200S, Operator'S Manual

Share
Download
Toro TimeCutter ZS 3200S Operator'S Manual Download Page 7

•

Replace all parts including, but not limited to, tires, belts,
blades, and fuel system components with original Toro
parts.

•

Check the brake operation frequently. Adjust and service
the brake as required.

Model 74650

Sound Pressure

This unit has a sound pressure level at the operator’s ear of 87
dBA, which includes an Uncertainty Value (K) of 1 dBA.

Sound power level was determined according to the
procedures outlined in EN ISO 5395:2013.

Sound Power

This unit has a guaranteed sound power level of 100 dBA,
which includes an Uncertainty Value (K) of 1 dBA.

Sound pressure level was determined according to the
procedures outlined in ISO 11094.

Hand/Arm Vibration

Measured vibration level for left hand = 2.1 m/s

2

Measured vibration level for right hand = 1.9m/s

2

Uncertainty Value (K) = 1.0 m/s

2

Measured values were determined according to the procedures
outlined in EN ISO 5395:2013.

Whole Body Vibration

Measured vibration level = 0.62 m/s

2

Uncertainty Value (K) = 0.31 m/s

2

Measured values were determined according to the procedures
outlined in EN ISO 5395:2013 (Riding and Stand-ons).

Model 74655

Sound Pressure

This unit has a sound pressure level at the operator’s ear of 89
dBA, which includes an Uncertainty Value (K) of 1 dBA.

Sound power level was determined according to the
procedures outlined in EN ISO 5395:2013.

Sound Power

This unit has a guaranteed sound power level of 100 dBA,
which includes an Uncertainty Value (K) of 1 dBA.

Sound power level was determined according to the
procedures outlined in ISO 11094.

Hand/Arm Vibration

Measured vibration level for left hand = 3.4 m/s

2

Measured vibration level for right hand = 2.4 m/s

2

Uncertainty Value (K) =1.7 m/s

2

Measured values were determined according to the procedures
outlined in EN ISO 5395:2013.

Whole Body Vibration

Measured vibration level = 0.73 m/s

2

Uncertainty Value (K) = 0.37 m/s

2

Measured values were determined according to the procedures
outlined in EN ISO 5395:2013(Riding and Stand-Ons).

7

 

Summary of Contents for TimeCutter ZS 3200S

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands