manualshive.com logo in svg

Toro LX Lawn Tractor, Service Manual

Share
Download
Toro LX Lawn Tractor Service Manual Download Page 171

MOWER DECK

7-17

LX Lawn Tractor Service Manual 

7

3.  Install the shoulder bolt between the brake bracket 

and the right hand idler bracket. Tighten the bolt and 
nut (Fig. 606).

5.  Install the extension spring between the brake arm 

and the right hand side belt cover (Fig. 608).

Note:  The extension spring installs in the upper 

hole on the belt cover.

 

Fig 606

 PICT-7888

 

Fig 608

 PICT-7851

4.  Install the extension spring between the left and right 

idler brackets (Fig. 607).

 

Fig 607

 PICT-7854

2.  Install the shoulder bolt and nut through the right 

hand idler bracket and the mower deck (Fig. 605).

Note:  Make sure the lower mower belt is routed 

to the inside of the right hand idler bracket 
assembly where it is mounted to the mower 
deck.

 

Fig 605

 PICT-7886

A.  Spring removal tool (Toro P/N 92-5771)

A

A

Summary of Contents for LX Lawn Tractor













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands