manualshive.com logo in svg

Toro LX Lawn Tractor, Service Manual

Share
Download
Toro LX Lawn Tractor Service Manual Download Page 168

MOWER DECK

7-14

 

LX Lawn Tractor Service Manual

7

46” Mower Deck - RH Idler Bracket 
Assembly

3.  Remove the mower deck belt cover from the mower 

deck (Fig. 596).

 

Fig 596

 PICT-7839

1.  Remove the mower Deck from the tractor. Refer to 

“46” Mower Deck Removal” on Page 7-69.

2.  Remove the 3 self-tapping screws securing the left 

mower deck belt cover to the mower deck (Fig. 595).

 

Fig 595

 PICT-7835

Removal

5.  Position the left belt cover onto the mower deck (Fig. 

593).

 

Fig 593

 PICT-9775

7.  Install the Mower Deck onto the tractor. Refer to “42” 

Mower Deck Installation” on page 7-67.

6.  Install the 3 self-tapping screws to secure the left 

belt cover to the mower deck (Fig. 594).

 

Fig 594

 PICT-9774

Summary of Contents for LX Lawn Tractor













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands