manualshive.com logo in svg

Toro LX Lawn Tractor, Service Manual

Share
Download
Toro LX Lawn Tractor Service Manual Download Page 126

ENGINE

4-12

  

LX Lawn Tractor Service Manual

4

22.  Lower the machine.

23.  Install the battery tray (Fig. 429).

25.  Install the battery hold down strap (Fig. 431).

 

Fig 429

 PICT-7277

 

Fig 431

 PICT-7497

26.  Connect the positive battery cable and then the 

negative battery cable.

27.  Install the mower deck:  42” deck on page 7-67; 46” 

deck on page 7-72; 50” deck on page 7-76.

28.  Fill the engine with oil per the engine specifi cations.

29.  Add fuel to the fuel tank.

30.  Check the throttle adjustment. Refer to “Throttle/

Choke Cable Replacement - Installation”, steps 7 
through 12 starting on page 3-97.

24.  Place the battery into the battery compartment (Fig. 

430).

 

Fig 430

 PICT-7276

Summary of Contents for LX Lawn Tractor













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands