Toro Groundsmaster 4000-D Service Manual Download Page 200

Page: 200 / 298

Groundsmaster 4000--D

Page 5 -- 26

Electrical System

Temperature Sender

The temperature sender is located near the alternator

on the water flange attached to the engine cylinder head

(Fig. 39). The resistance of the temperature sender re-

duces as the engine coolant temperature increases.

There is a gray harness wire attached to the terminal of

the switch.

Testing

1. Lower coolant level in the engine and remove the

temperature sender from water flange.

2. Suspend sender in a container of oil with a thermom-

eter and slowly heat the oil (Fig. 40).

CAUTION

Handle the hot oil with extreme care to prevent

personal injury or fire.

NOTE:

Prior to taking resistance readings with a digital

multi meter, short the meter test leads together. The me-

ter will display a small resistance value (usually 0.5

ohms or less). This resistance is due to the internal re-

sistance of the meter and test leads. Subtract this value

from from the measured value of the component you are

testing.

3. Check resistance of the sender with a multimeter

(ohms setting) as the temperature increases. Replace

sender if specifications are not met.

COOLANT TEMP TEMP SENDER RESISTANCE

100

F (38

460 ohms (approximate)

160

F (71

140 ohms (approximate)

200

F (93

54 to 78 ohms

221

F (105

50 ohms (approximate)

4. After testing is complete, install sender to the water

flange.

A. Thoroughly clean threads of water flange and

sender. Apply thread sealant to the threads of the

sender.

B. Screw sender into the water flange. Torque send-

er from

16 to 20 ft--lb (22 to 27 N--m)

C. Reconnect gray harness wire to sender. Apply

skin--over grease (Toro Part No. 505--165) to sender

terminal.

5. Fill engine cooling system.

Figure 39

1. Temperature sender

2. Alternator

Figure 40

Summary of Contents for Groundsmaster 4000-D











































































































































































































































































































Search results

Summary of Contents for Groundsmaster 4000-D

Reviews:

Related manuals for Groundsmaster 4000-D

Brands by name

Popular brands

Toro Groundsmaster 4000-D, Service Manual

Search results

Summary of Contents for Groundsmaster 4000-D

Reviews:

Related manuals for Groundsmaster 4000-D

Brands by name

Popular brands