Toro GrandStand 74534 Service Manual Download

Page: 108 / 268

CONTROLS

4-41

36” & 40” Toro GrandStand Service Manual

19. Pull the RH and LH slider spacers rearward as far as

possible (Fig. 333).

Fig. 333

DSCN-3812a

20. Tighten the clamp assembly to secure the cable to

the slider assembly (Fig. 334).

A. Left cable adjustment B. Right cable adjustment

Fig. 334

DSCN-3811a

Adjusting the Tracking

Note: Determine the left and right sides of the

machine from the normal operating position.

1. While driving the machine, push both control levers

forward the same distance.

2. Check if the machine tracks to one side. If it does,

stop the machine and set the parking brake.

3. Release the operator cushion from the rear of the

machine.

4. Rotate the right cable adjustment to position the

right motion control in the center of the control

panel neutral lock slot. Then, rotate the left cable

adjustment in quarter-turn increments until the

machine tracks straight (Fig. 335).

Note: Only adjust the left cable to match the left

wheel speed to the right wheel speed. Do

not adjust the right wheel speed as this will

position the right motion control lever out of

the center for the control panel neutral lock

slot.

Fig. 335

fig. 55 G012898

Summary of Contents for GrandStand 74534













































































































































































































































































Search results

Summary of Contents for GrandStand 74534

Reviews:

Related manuals for GrandStand 74534

Brands by name

Popular brands

Toro GrandStand 74534, Service Manual

Search results

Summary of Contents for GrandStand 74534

Reviews:

Related manuals for GrandStand 74534

Brands by name

Popular brands