Toro 41569 Installation Instructions Manual Download Page 11

11

Connecting the Spray Hose

1. Wrap Teflon tape counterclockwise around the threads

of the hose fitting on the long hose and install the fitting
into the connecting tube on the reel (Fig. 29).

m–6393

Figure 29

2. Connect the free end of the long hose to the fitting on

the gun (Fig. 30).

m–6392

2

3

1

Figure 30

1.

Spray gun

2.

Hose fitting

3.

Hose

3. Secure the end of the hose with a small plastic hose

clamp.

4. Connect the negative battery wire to the battery and

turn the ignition key to the Run position.

5. Press the hose wind button and carefully guide the hose

onto the reel.

Hands, loose clothing, long hair, and jewelry could
get caught in the hose and reel while rewinding
and cause injury.

Keep your hands clear of the reel and hose while
it is rewinding.

Do not wear loose clothing or jewelry and tie up
long hair.

Caution

Safety Instructions

Improper use or maintenance by the operator or owner
can result in injury. To reduce the potential for injury,
comply with these safety instructions and always pay
attention to the safety alert 

 symbol, which means

CAUTION, WARNING, or DANGER—“personal
safety instruction.” Failure to comply with the
instruction may result in personal injury or death.

Read also the safety and operation instructions in the
vehicle Operator’s Manual.

Do not aim the hand sprayer at any person or animal.
Fluids under high pressure can penetrate skin and cause
severe injury, possibly resulting in amputation or death.
Hot liquids and chemicals can also cause burns or
injury.  If any part of the body comes in contact with the
spray stream, immediately consult a physician familiar
with injected fluid injuries.

Do not place your hand or any other part of you body in
front of the spray nozzle.

Do not leave the equipment under pressure when you
are not present.

Do not use the hand sprayer if the hose, trigger lock,
nozzle, or any other part is damaged or missing.

Do not use the hand sprayer if there are any leaks in any
hoses, fittings, or other components.

Do not spray near power lines.

Do not drive while spraying with a hand sprayer.

Wear rubber gloves, safety goggles, and a full body
protective suit when spraying chemicals with the hand
sprayer.

Summary of Contents for 41569

















Reviews: