background image

DANGER

In certain conditions during fueling, static
electricity can be released causing a spark which
can ignite the gasoline vapors. A fire or explosion
from gasoline can burn you and others and can
damage property.

Always place gasoline containers on the ground
away from your vehicle before filling.

Do not fill gasoline containers inside a vehicle or
on a truck or trailer bed because interior carpets
or plastic truck bed liners may insulate the
container and slow the loss of any static charge.

When practical, remove gas-powered equipment
from the truck or trailer and refuel the equipment
with its wheels on the ground.

If this is not possible, then refuel such
equipment on a truck or trailer from a portable
container, rather than from a gasoline dispenser
nozzle.

If a gasoline dispenser nozzle must be used,
keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete.

WARNING

Gasoline is harmful or fatal if swallowed. Long-term
exposure to vapors can cause serious injury and
illness.

Avoid prolonged breathing of vapors.

Keep your face away from the nozzle and fuel
tank or conditioner opening.

Keep gasoline away from your eyes and skin.

Using Stabilizer/Conditioner

Use a fuel stabilizer/conditioner in the machine to provide
the following benefits:

Keeps gasoline fresh during storage of 90 days or less.
For longer storage it is recommended that the fuel tank
be drained.

Cleans the engine while it runs

Eliminates gum-like varnish buildup in the fuel system,
which causes hard starting

Important:

Do not use fuel additives containing

methanol or ethanol.

Add the correct amount of gas stabilizer/conditioner to the
gas.

Note:

A fuel stabilizer/conditioner is most effective when

mixed with fresh gasoline. To minimize the chance of varnish
deposits in the fuel system, use fuel stabilizer at all times.

Filling the Fuel Tank

1.

Shut the engine off.

2.

Clean the area around the fuel tank cap and remove
the cap (

Figure 13

).

Note:

The fuel tank cap contains a gauge which shows

the fuel level.

G020714

Figure 13

1.

Fuel tank

3.

Add unleaded regular gasoline to the fuel tank, until the
level is 6 mm to 13 mm (1/4 to 1/2 inch) below the
bottom of the filler neck.

Note:

This space in the tank allows gasoline to

expand. Do not fill the fuel tanks completely full.

4.

Install fuel tank cap securely.

5.

Wipe up any gasoline that may have spilled.

Checking the Engine-Oil Level

Before you start the engine and use the machine, check the oil
level in the engine crankcase; refer to

Checking the Engine

Oil Level (page 22)

.

Checking the Tire Pressure

Check the tire pressure (

Figure 14

).

The correct tire pressure is 241 kPa (35 psi).

Figure 14

13

 

Summary of Contents for 31500000

































Reviews: