background image

Form No. 3410-508 Rev A

Electric Lift Kit

TM5490/TM7490 Trailed Mowers

Model No. 02861—Serial No. 400000000 and Up

Installation Instructions

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm.

This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at
the back of this publication.

Safety

Before installing the kit:

Read the machine

Operator's Manual

and these

Installation

Instructions

.

Always wear eye protection.

Important:

Always seek professional advice from your

local authorized dealer if, after studying this, you are
unsure how to install this kit.

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or missing.

decal111-1777

111-1777

1.

Cutting unit rotation control

4.

Reverse rotation

7.

Right wing arm lift control

2.

Forward rotation

5.

Left wing arm lift control

8.

Override lift control

3.

Disengage cutting cylinder

6.

Center 3 or 5 arm lift control

9.

Emergency stop

© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the UK

All Rights Reserved

*3410-508* A

 

Summary of Contents for 02861

















Reviews: