1
2
3 4
5
19
21
4
20
18 17
16 15
6
7
12
10
11
8
9
7
10
14
13
G025354
g025354
Figure 15
1.
Solenoid (12 volt)
13.
Bush
2.
Solenoid valve (closed)
14.
Valve cylinder
3.
Line body
15.
Bonded seal (3/4 inch)
4.
Bonded seal (3/8 inch)
16.
Adapter (1/4 inch male x
3/4 inch male)
5.
Adapter (1/4 inch female x
3/8 inch male)
17.
Swivel tee (1/4 inch female
x 1/4 inch female x 1/4
inch female)
6.
Bonded seal (1/4 inch)
18.
Adapter (1/4 inch male x
1/4 inch male), 0.8 mm
orifice
7.
Hose (1/4 inch x 38 cm),
90° x straight
19.
Hose (1/4 inch x 2.156 m),
to the front solenoid valve
8.
Tee (1/4 inch male x
1/4 inch male x 1/4 inch
female)
20.
Adapter (1/4 inch male x
3/8 inch male)
9.
Adapter (1/4 inch male x
1/4 inch male), 1.4 mm
orifice
21.
Split pin
10.
Spring (existing)
22.
Cable ties (8), not shown
11.
Cylinder rod spring pin
23.
Large hose tie (368 x 4.8
mm), not shown
12.
Washer (10 mm)
9.
Remove the backlap release lever from the rear hole,
and install it into the front hole (
1
2
3
G025364
g025364
Figure 16
1.
Front slot
3.
Front hole
2.
Rear hole
10.
Fit the rotary valve cylinder assembly in the front slot
(
), and secure it using the original bolt and
slide bush.
11.
Attach the cylinder to the rotary bracket using the
washer (10 mm) and the split pin.
12.
Fit the 1/4 inch female tee and the 1/4 inch male
adapter (0.8 mm orifice) to the cylinder port, and
connect the hose from the front solenoid valve.
13.
Disconnect the hose on the lower 1/4 inch port of the
rear manifold. Fit a 1/4 inch male tee to the port, and
connect the hose.
14.
Assemble a line body with a solenoid valve and
solenoid. Fit a 3/8 inch bonded seal and a 3/8 inch x
1/4 inch male adapter (existing), to port 1 of the line
body. Fit a 3/8 inch bonded seal, a 3/8 inch x 1/4 inch
adapter, a 1/4 inch bonded seal, and a 1/4 inch male
adapter (1.4 mm orifice) to port 1 of the line body.
Connect the assembly to the valve cylinder line body.
15.
Connect the hose to the tee on the rear manifold.
Connect the other end to the fittings on the valve
cylinder line body.
16.
Run the cables from the control box to the rear
solenoid valve and the proximity switch bracket along
the center of the machine (under the hydraulic tank) to
the rear. Connect the cables to the solenoid and the
switch, respectively.
17.
Keep the rear solenoid cable and the rear cylinder hose
tidy by using the 8 cable ties and the large hose tie (368
x 4.8 mm) to secure them to the existing hoses under
the hydraulic oil tank.
18.
Check all the fasteners and hose connections, and
tighten them as necessary.
9
