background image

Form No. 3443-350 Rev A

Reverse 4WD Kit

LT-F3000 Triple Flail, LT3340 Triple Reel, or LT2240 Compact Triple
Turf Mower

Model No. 02858—Serial No. 400000000 and Up

Installation Instructions

This kit provides improved traction in reverse when traction is reduced in certain ground conditions.

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Description

Qty.

Use

No parts required

Prepare the machine.

High-pressure valve

2

Coil

2

Nut

2

Install the rear traction-manifold solenoids.

Adapter fitting (1/4 x 7/16 inch)—Model
31654, and Models 31657 and 31659 with the
optional differential-lock kit.

1

Seal (1/4)—Models 31657 and 31659 with the
optional differential-lock kit.

1

Quick-connect fitting—Model 31654, and
Models 31657 and 31659 without the optional
differential-lock kit.

1

Dust cap—machines without the optional road
light kit.

1

Reducer fitting (3/4 x 7/16 inch)—Models
31657 and 31659 without the optional
differential-lock kit.

1

Install the pressure test fitting.

Hydraulic test equipment 260 to 325 bar (3771
to 4714 psi), with a quick-disconnect fitting
(facility provided)

.

Prepare to test hydraulic pressure.

Hydraulic test equipment 260 to 325 bar (3771
to 4714 psi) with a Quick-Connect Fitting
(machines without the optional differential-lock
kit) or a Minimess™ fitting (machines with the
optional differential-lock kit)—facility provided

.

Prepare to test hydraulic pressure.

No parts required

Connect the battery and installing the storage
compartment.

No parts required

Test the hydraulic pressure.

No parts required

Finish the hydraulic test.

No parts required

Finish the hydraulic test.

No parts required

Check the hydraulic-fluid level.

© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the UK

All Rights Reserved

*3443-350*

 

Summary of Contents for 02858

















Reviews: