Topway LMT056DIDFWD-ABN, User Manual

Page: 11 / 14

TOPWAY
LCD Module User Manual
LMT056DIDFWD-ABN
Document Name: LMT056DIDFWD-ABN-Manual-Rev0.2
Page: 11 of 14
8.1.5 Command Table(continue)
Code (hex) Command Description
0xB0 set_lcd_mode_ Set the LCD panel mode and resolution
0xB1 get_lcd_mode Get the current LCD panel mode, pad strength and resolution
0xB4 set_hori_period Set front porch
0xB5 get_hori_period Get current front porch settings
0xB6 set_vert_period Set the vertical blanking interval between last scan line and next LFRAME
pulse
0xB7 get_vert_period Set the vertical blanking interval between last scan line and next LFRAME
pulse
0xB8 set_gpio_conf Set the GPIO configuration. If the GPIO is not used for LCD, set the
direction. Otherwise, they are toggled with LCD signals.
0xB9 get_gpio_conf Get the current GPIO configuration
0xBA set_gpio_value Set GPIO value for GPIO configured as output
0xBB get_gpio_status Read current GPIO status. If the individual GPIO was configured as input,
the value is the status of the corresponding pin. Otherwise, it is the
programmed value.
0xBC set_post_proc Set the image post processor
0xBD get_post_proc Set the image post processor
0xBE set_pwm_conf Set the image post processor
0xBF get_pwm_conf Set the image post processor
0xC0 set_lcd_gen0 Set the rise, fall, period and toggling properties of LCD signal generator 0
0xC1 get_lcd_gen0 Get the current settings of LCD signal generator 0
0xC2 set_lcd_gen1 Set the rise, fall, period and toggling properties of LCD signal generator 1
0xC3 get_lcd_gen1 Get the current settings of LCD signal generator 1
0xC4 set_lcd_gen2 Set the rise, fall, period and toggling properties of LCD signal generator 2
0xC5 get_lcd_gen2 Get the current settings of LCD signal generator 2
0xC6 set_lcd_gen3 Set the rise, fall, period and toggling properties of LCD signal generator 3
0xC7 get_lcd_gen3 Get the current settings of LCD signal generator 3
0xC8 set_gpio0_rop Set the GPIO0 with respect to the LCD signal generators using ROP
operation. No effect if the GPIO0 is configured as general GPIO.
0xC9 get_gpio0_rop Get the GPIO0 properties with respect to the LCD signal generators.
0xCA set_gpio1_rop Set the GPIO1 with respect to the LCD signal generators using ROP
operation. No effect if the GPIO1 is configured as general GPIO.
0xCB get_gpio1_rop Get the GPIO1 properties with respect to the LCD signal generators.
0xCC set_gpio2_rop Set the GPIO2 with respect to the LCD signal generators using ROP
operation. No effect if the GPIO2 is configured as general GPIO.
Hex Code Command Description
0xCD get_gpio2_rop Get the GPIO2 properties with respect to the LCD signal generators.
0xCE set_gpio3_rop Set the GPIO3 with respect to the LCD signal generators using ROP
operation. No effect if the GPIO3 is configured as general GPIO.
0xCF get_gpio3_rop Get the GPIO3 properties with respect to the LCD signal generators.
0xD0 set_dbc_conf Set the dynamic back light configuration
0xD1 get_dbc_conf Get the current dynamic back light configuration
0xD4 set_dbc_th Set the threshold for each level of power saving
0xD5 get_dbc_th Get the threshold for each level of power saving
0xE0 set_pll Start the PLL. Before the start, the system was operated with the crystal
oscillator or clock input
0xE2 set_pll_mn Set the PLL
0xE3 get_pll_mn Get the PLL settings
0xE4 get_pll_status Get the current PLL status
0xE5 set_deep_sleep Set deep sleep mode
0xE6 set_lshift_freq Set the LSHIFT (pixel clock) frequency
0xE7 get_lshift_freq Get current LSHIFT (pixel clock) frequency setting
0xE8 Reserved Reserved
0xE9 Reserved Reserved
0xF0 set_pixel_data_interface Set the pixel data format of the parallel host processor interface
0xF1 get_pixel_data_interface Get the current pixel data format settings
0xFF Reserved Reserved
Note. Please Refer to SSD1963 datasheet for details.
ZZZWRSZD\GLVSOD\VHX
LQIR#WRSZD\GLVSOD\VHX