TOOLSPACE XW-1201 Manual Download Page 13

f.  In the event of cell leakage, contact with the skin or eyes should be avoided. If affected, 

wash the affected areas with plenty of water and seek medical advice.

g. 

rer. 

h.   The plus (+) and minus (-) markings on the battery and device should be 

 and 

used correctly.

i.   
j.  The device mustn‘t combine items of a different brand, capacity, size or type.
k.   Children shouldn‘t use battery-packs or batteries unless under adult supervision.
l.  If a cell or battery is swallowed, you should seek medical attention immediately.
m.   Always purchase batteries that are recommended by the device manufacturer.
n.   Keep battery-packs or batteries and cells clean and dry.
o.   If cells or battery terminals become dirty, they should be cleaned with a clean, dry cloth.
p.   Battery-packs and batteries must be charged before use. Always use the correct charger 

and follow the manufacturer's instructions or operating instructions.

q.  Don‘t charge the battery-pack or battery for a long periods when not in use.
r.   After prolonged storage, it may be better to recharge and discharge the battery-pack or 

battery several times to maximise battery performance.

s.   The original battery-pack and battery documentation should be retained for future use.
t.   Rechargeable battery-packs or batteries should only be used for purposes for which 

they are intended.

u.   When not in use, battery-packs or batteries should be removed, if at all possible.
v.   Disposal of battery-packs and batteries must be carried out in accordance with applicable 

regulations. 

Dead batteries do not belong in household waste.

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY 

CHARGERS

 

 CAUTION! 

Risk of injury resulting from electric shock.

Before  each  use,  check  the  charger,  cable  and  plug.  If  you 

  damage,  do  not  use 

the charger.

a.  Be sure to read all instructions and warning labels on the charger and the battery 

casing.

b.  Do not expose the charger to rain, snow or moisture. Water entering the charger 

increases the risk of electric shock.

c.  Reduce the possibility of damage to the plug and the power cord by disconnecting 

the plug from the wall outlet always by the plug end (do not pull on the cable). 

Make sure the cord is positioned so no one can step on it, trip over it or to prevent other 
damage.

d.  Never  charge  the  battery  in  hazardous  areas  and  near  to  combustibles,  or  in 

  environments.  Do  not  operate  the  charger  on  an  easily 

surface (e.g. paper, textiles, etc.).

e.  Do not disassemble the charger. If it needs to be replaced or repaired, take it to 

an authorised service centre. Unprofessional intervention can result in the risk of 

re.

Summary of Contents for XW-1201





















Reviews: