background image

1

2

 WARNING: 

Read carefully and understand all 

ASSEMBLY AND OPERATION INSTRUCTIONS

 before 

operating. Failure to follow the safety rules and other basic safety precautions may result in 

serious personal injury.

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

 Failure to follow all instructions listed 

below may result in serious injury.

CAUTION:  Do  not  allow  persons  to  operate  or  assemble  this  POWER  CUT  25K 

machine until they have read this manual and have developed a thorough understanding 

of how the POWER CUT 25K works.

WARNING:  The  warnings,  cautions,  and  instructions  discussed  in  this  instruction 

manual cannot cover all possible conditions or situations that could occur. 

It must be 

understood by the operator that common sense and caution are factors which cannot be 

built into this product, but must be supplied by the operator.

IMPORTANT SAFETY CONSIDERATIONS

1.1 Your Cutting Environment

- Keep the environment you will be cutting in free from flammable materials.

- Always keep a fire extinguisher accessible to your cutting environment.

- Always have a qualified person install and operate this equipment.

- Make sure the area is clean, dry and ventilated. Do not operate the cutter in humid, wet or 

poorly ventilated areas.

-  Always  have  your  cutter  maintained  by  a  qualified  technician  in  accordance  with  local, 

state and national codes.           

-  Always  be  aware  of  your  work  environment.  Be  sure  to  keep  other  people,  especially 

children, away from you while welding. 

- Keep harmful arc rays shielded from the view of others.

- Mount the cutter on a secure bench or cart that will keep the cutter secure and prevent it 

from tipping over or falling.

1.2 Your Cutter Condition

- Check ground cable, power cord and cutting cable to be sure the insulation is not damaged. 

Always replace or repair damaged components before using the cutter.

- Check all components to ensure they are clean and in good operating condition before use.

1.3 Use of Your Cutter

 

   

Do not operate the cutting if the output cable, electrode, torch, wire is wet. Do not immerse 

them in water. These components and the Cutter must be completely dry before attempting 

to use them.

WARRANTY

This product is guaranteed against defects for lifetime of the product. This warranty is 
provided  by  Super  Cheap  Auto  Pty  Ltd  ACN  085  395  124  (Supercheap  Auto)  of  751 
Gympie Rd Lawnton QLD 4501 Ph (07) 3482 7500. Supercheap Auto will offer a repair, 
replacement product or store credit if the product is assessed as being defective during 
the warranty period. 

To claim under this warranty, take this product to the Front Service Desk of your nearest 
Supercheap Auto store.  For store locations, visit www.supercheapauto.com.au (AUS) 
or  www.supercheapauto.co.nz  (NZ).  You  will  need  your  receipt  or  proof  of  purchase.  
Additional information may be requested of you to process your claim.  Should you not 
be able to provide proof of purchase with a receipt or a bank statement, identification 
showing your name, address and signature may be required to process your claim. 

This  product  may  need  to  be  sent  to  the  manufacturer  to  assess  the  defect  before 
determining any claim. Faults or defects caused by product modification, misuse and 
abuse, normal wear and tear or failure to follow user instructions are not covered under 
this warranty. 

Our goods come with guarantees that cannot be excluded under the Australian Consumer 
Law.  You are entitled to a replacement or refund for a major failure and for compensation 
for any other reasonably foreseeable loss or damage.  You are also entitled to have the 
goods repaired or replaced if the goods fail to be of acceptable quality and the failure 
does not amount to a major failure.

Any expenses incurred relating to the return of this product to store will normally have 
to be paid by you.  For more information contact your nearest Supercheap Auto store.
The benefits to the consumer given by this warranty are in addition to other rights and 
remedies of the Australian Consumer Law in relation to the goods and services to which 
this warranty relates.

Summary of Contents for POWER CUT 25K














Reviews: