Figure A
Figure B
90°
Figure C
Figure D
c) Personal
• Do not operate equipment while under the
influence of drugs or alcohol.
• Do not wear loose clothing, hair jewelry etc. whilst
using the drill stand as these may get caught in
the drill.
• Operators must always wear impact resistant
protective goggles with side protectors, protective
masks, gloves, and hearing protection while
operating the product with drill attached.
• Operators and maintenance personnel shall be
physically able to handle the bulk, weight and
power of the tool.
• Keep proper footing at all times in order to ensure
correct balance when working.
d) Connected devices
• Also observe the safety and operating
instructions of any other devices which are used
in conjunction with the product.
• Protect the drill against accidental starts, or
disconnect from power supply when inserting or
removing from the stand, making adjustments, or
when not in use.
Assembly
See figure A.
1. Remove the frame mounting screws
(10)
.
2. Insert the frame into the angle guide slots on the
base, then replace the mounting screws.
3. Tighten the angle lock screws
(8)
to secure the
frame to the base.
4. Check that the handle
(3)
is properly secured by
turning it clockwise.
Operation
Do not use as router. The base
should always be secured to the work
piece when drilling. Work on a stable
workbench and clamp the work piece
tightly.
Check all components for damage
and make sure everything is properly
fastened before starting work.
When setting up or making
adjustments, always disconnect the
drill from the power source to prevent
accidental starts.
a) Setting up
1. Loosen the clamp bolts using a hex key (not
included) then mount the drill.
2. Slightly loosen the backstop screw
(7)
and depth
stop screw
(4)
3. Place the drill over the edge of the work piece
and press down to the desired drill depth.
4. Tighten the backstop screw, then slide the depth
stop all the way up against the clamp, then
tighten the depth stop screw.
5. Release backstop screw to begin working.
b) Drilling round work-pieces.
See figure B
Center the work piece along the V-groove
(2)
. Use
the insert
(11)
for increased stability if needed.
c) Using a hole saw
See figure C
d) Drilling at an angle
See figure D
1. Loosen both angle lock screws
(8)
and adjust to
the desired angle.
Refer to the angle guide
(9)
markings for
precise adjustments.
2. Tighten the angle lock screws to lock the angle.
Care and cleaning
• This product is maintenance free. Let the drill
cool down and disconnect from the power source
before removing it from the clamp.
• Do not use any aggressive cleaning agents,
rubbing alcohol or other chemical solutions as
they can cause damage to the housing and
malfunctioning.
•
Clean the product with a dry, fibre-free cloth.
Technical data
Holding diameter ................43 mm
Dimensions ......................... 235 x 145 x 275 mm
(L x W x H)
Weight ................................1.1 kg
Operating Instructions
Mobile Drill Stand
Item No. 1698511
Intended use
This drill stand is intended to be used for accurate
centering and angle drilling up to 45 degrees. It
provides control, leverage, increased efficiency when
performing repetitive tasks, and has an adjustable
depth stop. It can house most 43 mm hand drills that
have not been modified.
It is intended for indoor use only. Do not use it
outdoors. Contact with moisture, e.g. in bathrooms,
must be avoided under all circumstances.
For safety and approval purposes, you must not
rebuild and/or modify this product. If you use the
product for purposes other than those described
above, the product may be damaged. In addition,
improper use can result in short circuits, fires,
or other hazards. Read the instructions carefully
and store them in a safe place. Make this product
available to third parties only together with its
operating instructions.
This product complies with the statutory national and
European requirements. All company names and
product names are trademarks of their respective
owners. All rights reserved.
Delivery content
• Main unit
• Round plate
• Metal base stand
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.
conrad.com/downloads or scan the QR code shown.
Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation
mark in the triangle is used to indicate
important information in these
operating instructions. Always read this
information carefully.
The arrow symbol indicates special
information and advice on operation.
Safety instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do not
follow the safety instructions and
information on proper handling in
this manual, we assume no liability
for any resulting personal injury or
damage to property. Such cases will
invalidate the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of
children and pets.
• Do not leave packaging material lying around
carelessly. This may become dangerous playing
material for children.
• Protect the device from extreme temperatures,
direct sunlight, strong jolts, high humidity,
moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical
stress.
• If it is no longer possible to operate the product
safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer
be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor
ambient conditions or
- has been subjected to any serious transport-
related stresses.
• Please handle the product carefully. Jolts,
impacts or a fall even from a low height can
damage the product.
• Consult an expert when in doubt about the
operation, safety or connection of the device.
• Maintenance, modifications and repairs must only
be completed by a technician or an authorised
repair centre.
• If you have questions which remain unanswered
by these operating instructions, contact our
technical support service or other technical
personnel.
• In schools, training facilities, hobby or self-service
workshops, handling of this product must be
monitored by trained personnel.
• When operating on commercial premises,
relevant accident prevention regulations must be
observed.
b) Work area
• The workplace must always be kept clean and
tidy. Mess at the workplace increases probability
of dangerous incidents.
• Make sure the work area is clear of debris,
obstructions and well lit.
• Keep children and bystanders at a safe distance
when using the tool.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
*1698511_v1_0520_02_dh_m_en
Operating Elements
1 2
3
9
10
4
5 6 7 8
11
1 Base mounting point (screws
not included)
2 V-groove
3 Handle
4 Depth stop screw
5 Clamp
6 Clamp bolt
7 Back stop screw
8 Angle lock screw
9 Angle guide
10 Frame mounting screws
11 Insert
