This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
*1561694-6_v5_1219_02_dh_m_4L
Stage 2
The second stage will start automatically.
• The temperature of the soldering tip is controlled.
• This is displayed again with a countdown from 30 to 0.
•
The soldering tip temperature will be stable after approximately five minutes. The temperature
is below 400 °C.
Always Avoid drafts during calibration. This may negatively influence calibration.
Stage 3
The third stage will start automatically.
• The temperatures will be measured and set.
• The display shows the following screen.
• The “TMP” line shows three dashes, the “SET” line shows the value of the temperature
controller - depending on its current position.
• Now measure the temperature at the soldering tip with a precise measuring probe and read
the actual temperature at the thermometer.
Use a small measuring probe for the measurement, since large-area sensors may
falsify the result. K-type thermal sensors are well suitable.
• Set the value read at the temperature controller. Turning the temperature controller dial
changes the value in the “SET” line.
•
Briefly push the button “PRESET 2”. The setting menu is terminated and the current soldering
tip temperature is displayed.
• End of calibration procedure is followed with message “SUCCESS! RESTART”
• Turn soldering station OFF and On to restart.
If calibration is started by accident, you can terminate it at any time by switching off
before pushing the button “PRESET 2”. The pre-set values are retained.
Replacement of Soldering Tip
1. Turn off the soldering station and let the soldering iron cool down completely.
2. Loosen the soldering tip locking screw from the soldering iron and pull the bracket off.
3. Carefully pull the soldering tip in a straight line from the ceramic heating element of the
soldering iron.
4. Insert a new tip on to the ceramic heating element.
5. Place the cap nut in its position and tighten it carefully. Do not use force when screwing; do
not use any tool!
6. Calibrate your new tip (see “Calibration”).
The ceramic heating element must not be mechanically stressed. In case of damage
to the ceramic heating element, the warranty will become void.
Maintenance and Cleaning
The soldering station is maintenance-free, except for the occasional replacement of the
soldering tip or sponge.
• Disconnect the product from the mains before each cleaning and let cool down.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
•
Clean the product with a dry, fibre-free cloth.
Changing the Fuse
1. Switch the power off. Remove the mains plug from the mains socket.
2. The back of the soldering station contains the fuse holder with the inserted fuse.
3. Pull out the fuse holder with a suitable screwdriver.
4. Replace the defective fuse with a new one of the same type and rated data (see “Technical
Data”).
If the fuse goes out again after starting the soldering station, turn off the soldering
station and unplug the power cord from the power outlet. Don’t use the soldering
station anymore; get it checked by an expert.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Soldering station type
ST-50D
ST-80D
ST-100D
Item no.
1561694
1561695
1561696
Operating voltage
230 V/AC, 50 Hz
Power input
max. 65 W
max. 100 W
max. 118 W
Soldering iron voltage
24 V/AC
Soldering iron output
50W
80W
100W
Temperature of the soldering tip
150 °C to 450 °C (adjustable)
Heat up time (25°C to 450°C)
120s
80s
60s
ESD/Equipotential bonding
socket
Socket connection (Ø 4 mm)
Safety type
5 x 20 mm
Fuse value
250 V, 400 mA,
slow-blow
250 V, 630 mA,
slow-blow
250 V, 630 mA,
slow-blow
Weight of soldering station
1,750 g
2,030 g
2,350 g
Cable length of soldering iron
approx. 100cm
Dimensions of the soldering
station (W x H x D)
122 x 99 x 178 mm
Dimensions of the soldering iron
holder stand (W x H x D)
71 x 85 x 158 mm
