background image

 

12

WARNING  ;

  Do not perform sudden lifts or sudden 

lowering of the hoist.   Also, do not suddenly operate the 

hoist in the opposite direction. ( See diagram 4 )   

This  will  lead  to  damage  of  the  wire  rope  or  hoist  body.       

The load may also fall over leading to an accident.

 

 
2-4.  Do not lift people using the hoist 

WARNING ; 

This hoist is designed to lift loads.      Do not 

at any time try to lift people. ( See diagram 6) 

 
2-5.  Do not leave the hoist with a load 

WARNING ;

 Do not leave the hoist with a load.      When 

leaving a load, lower the load to a stable position and remove 

the hook from the load.      ( See diagram 7)

 

 
2-6.  Safe Operating position 

WARNING ; 

Do not operate the hoist under the load.   

Stay as far away from the load as possible while operating 

the hoist. 

 
2-7. 

Distance from load

 

WARNING ; 

Do not allow anyone except the operator of 

the hoist to be near the load.      ( See diagram 8) 

Anyone except the operator of the hoist should be at least 2 

meters away from the load/hoist. 

 
2-8. 

Signals at Job site

 

WARNING ; 

When using the hoist jointly with another 

person, use signals agreed at the job site and obey them 

during a joint operation. 

 
2-9.  Precautions during operation 

WARNING ; 

During operation of the hoist, do not touch 

the area of where the wire enters or moves.    This is very 

dangerous. 

 

[email protected]

Air & Allied Sales (Pacific) Pty Ltd

www.air-allied.com.au

Summary of Contents for TMM-140A





















Reviews: