TLV PowerTrap GP10F Instruction Manual Download Page 6

Page: 6 / 35

172-65378MA-03 (GP10F PowerTrap) 23 Apr 2019

General Description

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

Application

The PowerTrap is used to discharge liquid from vacuum-pressure or low-pressure areas
to high-pressure areas, or from lower to higher elevations.

There are two types of delivery systems (piping methods): the closed system and the
open system. The GP10F is for use with open systems. It can be used with closed
systems, but only where there is

always

negative

pressure differential (e.g. vacuum

equipment). Other PowerTrap models are available for different systems.

Check to make sure which PowerTrap model is most suitable for use on the type of
system that is being planned for installation.

Type of
System

Closed System

Open System

System
Overview

Equip-

ment

Reservoir

Condensate

Recovery Line

Exhaust

Pipe

Power

Trap

Equip-

ment

Reservoir

Power

Trap

Equip-

ment

Steam

Trap

Steam

Trap

Power

Trap

Equip-

ment

Receiver

Discharge to

Atmosphere

Condensate

Recovery line

Venting

Pipe

Exhaust

Pipe

Overflow Pipe

Equip-

ment

Steam

Trap

Steam

Trap

Power

Trap

Equip-

ment

Receiver

Discharge to

Atmosphere

Condensate

Recovery line

Venting

Pipe

Exhaust

Pipe

Overflow Pipe

Benefits



No need for external steam trap (GT
model features built-in trap)



No flash steam discharge



Small reservoir



Use with vacuum equipment possible



Collection of condensate from multiple
equipment possible



Can be used where trap is lower than
receiver, such as equipment situated
near grade (providing there is sufficient
differential pressure)

Notes



Only one piece of equipment possible
per system



Equipment has minimum height
requirement to ensure that condensate
flows naturally, by gravity

(approx.: GP14/GT14/GP10/GP10/
GT10 – 0.8 m (32 in); GP10F – 1 m
(40 in); GP10L/GT10L – 0.3 or 0.5 m
(12 or 20 in); GT5C – 170 mm (7 in))



Separate steam trap required for each
piece of equipment



Requires venting pipe to discharge
flash steam to atmosphere

Model

Mechanical pump with built-in trap

GT14/GT10/GT10L/GT14L/GT14M/
GT5C

Mechanical pump

GP14/GP10/GP10L/GP14L/GP14M/
GP5C/GP10F

Where there is

ALWAYS

negative

pressure differential
(e.g. vacuum equipment),

GP14/GP10/GP10L/GP14L/GP14M/
GP5C/GP10F

can be used

Summary of Contents for PowerTrap GP10F



































Search results

Summary of Contents for PowerTrap GP10F

Reviews:

Related manuals for PowerTrap GP10F

Brands by name

Popular brands

TLV PowerTrap GP10F, Instruction Manual

Search results

Summary of Contents for PowerTrap GP10F

Reviews:

Related manuals for PowerTrap GP10F

Brands by name

Popular brands