TLV PowerTrap GP10F Instruction Manual Download Page 8

Page: 8 / 35

172-65378MA-03 (GP10F PowerTrap) 23 Apr 2019

Specifications

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

Use only under conditions in which no freeze-up will occur. Freezing

may damage the product, leading to fluid discharge, which may cause

burns or other injury.

CAUTION

Refer to the product nameplate for detailed specifications.

Model

Serial Number

Maximum Allowable Temperature*(TMA)

Maximum Operating Temperature (TMO)

Maximum Allowable Pressure*

Maximum Operating Pressure

Valve No.**

Nominal Diameter

Motive Medium Pressure Range

0.03 to 1.05 MPaG (5 to 150 psig)

Max. Allowable Back Pressure

0.05 MPa (7 psi) less than motive medium pressure used

* Maximum allowable pressure (PMA) and maximum allowable temperature (TMA) are

PRESSURE SHELL DESIGN CONDITIONS,

NOT

OPERATING CONDITIONS.

** Valve No. is displayed for products with options. This item is omitted from the nameplate when there

are no options.

Configuration

Exhaust
Outlet

Plug

Intake Valve Unit

Motive Medium Inlet

Exhaust
Valve
Unit

Exhaust Outlet

Motive Medium

Inlet

Snap-action Unit

Float

Pumped
Medium
Outlet

Pumped

Medium

Inlet

Tank Unit
(Body)

Cover Gasket

NOTE:
Configuration of
tank/body may
differ slightly.

50 mm (2 in)

Pumped Medium Outlet

80 mm (3 in)

Pumped Medium Inlet

25 mm (1 in)

Exhaust Outlet

20 mm (¾ in)

Motive Medium Inlet

Size

Connection

Pumped Medium Outlet

Pumped Medium Inlet

Exhaust Outlet

Motive Medium Inlet

Size

Connection

GP10F Cover Unit

Summary of Contents for PowerTrap GP10F



































Search results

Summary of Contents for PowerTrap GP10F

Reviews:

Related manuals for PowerTrap GP10F

Brands by name

Popular brands

TLV PowerTrap GP10F, Instruction Manual

Search results

Summary of Contents for PowerTrap GP10F

Reviews:

Related manuals for PowerTrap GP10F

Brands by name

Popular brands