TLV PowerTrap GP10F Instruction Manual Download Page 27

Page: 27 / 35

172-65378MA-03 (GP10F PowerTrap) 23 Apr 2019

6. Removing/Reinstalling the Motive Medium Intake Valve and Valve Seat

The following procedure can be used to remove and replace the intake (motive
medium) valve without first removing the cover of the PowerTrap.

Part

Disassembly

Reassembly

Plug

• Using a 38 mm (1½ in) socket wrench,

remove the plug.

• Tighten to a torque of 160 N

⋅

(115 lbf

⋅

ft).

Plug Gasket

• Remove gasket and clean sealing

surfaces on the plug and the cover.

• Replace with a new gasket.

Motive Medium Intake
Valve

• Remove with needle-nose pliers

• Replace with new if damaged.

Screen

• Remove with needle-nose pliers

• Replace with new if damaged.

Motive Medium Intake
Valve Seat

• Using a 17 mm

(

in) socket wrench

with an extension bar, loosen the valve
seat.

• Using needle-nose pliers, grasp and

remove the valve seat.

• Using needle-nose pliers, insert

the valve seat.

• Tighten to a torque of 160 N

⋅

(115 lbf

⋅

ft)

Motive Medium Intake
Valve Seat Gasket

• Remove gasket with needle-nose

pliers and clean sealing surfaces.

• Replace with a new gasket.

(1 N

⋅

≈

10 kg

⋅

cm)

Plug

Plug Gasket

Screen

Motive Medium
Intake Valve

Motive Medium Intake
Valve Seat Gasket

Cover Unit

Motive Medium
Intake Valve Seat

NOTE: It is possible to remove and replace the intake valve (motive medium) without first

removing the cover of the PowerTrap (see instructions above).

Summary of Contents for PowerTrap GP10F



































Search results

Summary of Contents for PowerTrap GP10F

Reviews:

Related manuals for PowerTrap GP10F

Brands by name

Popular brands

TLV PowerTrap GP10F, Instruction Manual

Search results

Summary of Contents for PowerTrap GP10F

Reviews:

Related manuals for PowerTrap GP10F

Brands by name

Popular brands