TLV JL14-X Instruction Manual Download Page 17

Page: 17 / 19

172-65441A-04 (JL14-X/JLH14-X/JLH14-B) 20 Jan 2021

Problem

Diagnosis (Cause)

Remedy

Steam is
discharged or
leaks from the
trap outlet
(blowing)
(steam leakage)

Check sliding sections of lever unit:
- Is rust and/or scale obstructing movement of the

lever unit?

- Is the movement of the lever smooth?

Clean or replace with a
new lever unit

Check the air vent:

- Check for damage to or rust and scale on the X-

element or the bimetal

Replace parts where
necessary

Check for proper installation

Install correctly

Check for trap vibration

Lengthen the inlet
piping and fasten it
securely

Steam is
leaking from a
place other than
the outlet

Check for gasket deterioration or damage

Replace with new
gasket(s)

Check to make sure that the proper tightening
torques were used

Tighten to the proper
torque

Erosion has occurred in the body or cover

Replace with a new
product

Float frequently
becomes
damaged

Check to see if water hammer has occurred

Study and correct the
piping

Summary of Contents for JL14-X




















Search results

Summary of Contents for JL14-X

Reviews:

Related manuals for JL14-X

Brands by name

Popular brands

TLV JL14-X, Instruction Manual

Search results

Summary of Contents for JL14-X

Reviews:

Related manuals for JL14-X

Brands by name

Popular brands