Table of Contents
Safety Precautions ..................................................................2
Français ...............................................................................12
Español................................................................................14
General Description ................................................................4
Operation .................................................................................4
Pre-Start ................................................................................4
Purging and Priming ..............................................................4
Operating the Spray Gun ......................................................5
Pressure Relief Procedure ....................................................5
Spraying ...................................................................................6
Spraying Technique ...............................................................6
Practice..................................................................................6
Cleanup ....................................................................................7
Flushing the Unit ...................................................................7
Maintenance ............................................................................7
General Repair and Service Notes .......................................7
Daily Maintenance .................................................................8
Spray Gun Maintenance........................................................8
Accessories .............................................................................9
Troubleshooting ....................................................................10
Airless Pump .......................................................................10
Airless Gun ..........................................................................10
Spray Patterns .....................................................................11
Parts Lists and Service Instructions...................................16
Main Assembly ....................................................................16
Motor Assembly ...................................................................17
Gear Box Assembly .............................................................18
Fluid Section Assembly .......................................................20
Siphon Assembly .................................................................21
Filter Block Assembly ..........................................................22
Skid Assembly .....................................................................23
Warranty.................................................................................24
Safety Precautions
This manual contains information that must be read and
understood before using the equipment. When you come to an
area that has one of the following symbols, pay particular
attention and make certain to heed the safeguard.
This symbol indicates a potential hazard that may cause
serious injury or loss of life. Important safety information
will follow.
This symbol indicates a potential hazard to you or to the
equipment. Important information that tells how to prevent
damage to the equipment or how to avoid causes of minor
injuries will follow.
HAZARD: Injection injury - A high pressure stream
produced by this equipment can pierce the skin
and underlying tissues, leading to serious
injury and possible amputation. See a
physician immediately.
DO NOT TREAT AN INJECTION INJURY AS A SIMPLE CUT!
Injection can lead to amputation. See a physician
immediately.
The maximum operating range of the pump is 3200
PSI/221BAR fluid pressure.
WARNING
NOTE: Notes give important information which should
be given special attention.
CAUTION
WARNING
2
© Titan Tool Inc. All rights reserved.
PREVENTION:
• NEVER aim the gun at any part of the body.
• NEVER allow any part of the body to touch the fluid
stream. DO NOT allow body to touch a leak in the fluid
hose.
• NEVER put your hand in front of the gun. Gloves will not
provide protection against an injection injury.
• ALWAYS lock the gun trigger, shut the pump off, and
release all pressure before servicing, cleaning the tip or
guard, changing tip, or leaving unattended. Pressure will
not be released by turning off the motor. The
PRIME/SPRAY valve must be turned to PRIME to relieve
the pressure. Refer to the PRESSURE RELIEF
PRESSURE described in the pump manual.
• ALWAYS keep the tip guard in place while spraying. The
tip guard provides some protection but is mainly a warning
device.
• ALWAYS remove the spray tip before flushing or cleaning
the system.
• The paint hose can develop leaks from wear, kinking and
abuse. A leak can inject material into the skin. Inspect
the hose before each use.
• NEVER use a spray gun without a trigger lock and trigger
guard in place and in good working order.
• All accessories must be rated at or above 3200 PSI/221
BAR. This includes spray tips, guns, extensions, and
hose.
HAZARD: EXPLOSION OR FIRE - Solvent and paint fumes
can explode or ignite. Severe injury and/or
property damage can occur.
PREVENTION:
• Provide extensive exhaust and fresh air introduction to
keep the air within the spray area free from accumulation
of flammable vapors.
• Avoid all ignition sources such as static electric sparks,
open flames, pilot lights, and hot objects. Connecting or
disconnecting power cords or working light switches can
make sparks.
• Do not smoke in spray area.
• Fire extinguisher must be present and in good working
order.
• Place paint pump at a minimum of 3 feet (preferably
more) into a separate, well ventilated room from the spray
object or at least 20 feet from the spray object in a well
ventilated area (add more hose if necessary). Flammable
vapors are often heavier than air. Floor area must be
extremely well ventilated. The paint pump contains arcing
parts that emit spark and can ignite vapors.
• The equipment and objects in and around the spray area
must be properly grounded to prevent static sparks.
• Use only conductive or grounded high pressure fluid hose.
Gun must be grounded through hose connections.
• Power cord must be connected to a grounded circuit.
• Always flush unit into a separate metal container, at low
pump pressure, with spray tip removed. Hold gun firmly
against side of container to ground container and prevent
static sparks.
• Follow the material and solvent manufacturer's warnings
and instructions.
• Use extreme caution when using materials with a
flashpoint below 70° F (21° C). Flashpoint is the
temperature that a fluid can produce enough vapors to
ignite.
NOTE TO PHYSICIAN:
Injection into the skin is a traumatic injury. It is
important to treat the injury as soon as possible. DO
NOT delay treatment to research toxicity. Toxicity is a
concern with some coatings injected directly into the
blood stream. Consultation with a plastic surgeon or
reconstructive hand surgeon may be advisable.
